Emblem on ŠKODA Octavia A5 (2004–2013) is not just a design element, but a calling card of the car. It emphasizes that it belongs to a Czech brand and gives the car a complete look. However, over time, the logo may fade, crack, or fall off due to corrosion on the fasteners. In this article we will look at everything you need to know about emblems. Octavia A5: from original articles to step-by-step replacement instructions.
Owners often face problems: where to buy a high-quality replacement, how to properly remove the old emblem without damaging the hood, and which analogues are as good as the original. We've compiled expert advice, comparison charts and step by step instructions, so that you can cope with the task yourself - without contacting the service.
Original ŠKODA Octavia A5 emblems: items and dimensions
On Octavia A5 Two types of emblems were installed: on the hood (main) and on the trunk (additional). Original parts are produced under the brand ŠKODA and have unique catalog numbers. It is important to take into account the year of manufacture of the car - since 2008, the logo design has changed slightly (the lines of the winged arrow have become thicker).
Below are the current article numbers for different modifications:
| Emblem type | Article (before 2008) | Article (after 2008) | Size(mm) | Note |
|---|---|---|---|---|
| Main (hood) | 5E0 853 701 A |
5E0 853 701 B |
90×60 | Fastening with double-sided tape + caps |
| Rear (trunk) | 5E0 853 702 A |
5E0 853 702 B |
75×50 | Only adhesive base |
| Wheel cap emblem | 5E0 601 171 A |
5E0 601 171 B |
45×45 | Plastic holder |
⚠️ Attention: When purchasing, check the compatibility of the article with the VIN number of your car. Emblems for restyled versions (2009–2013) may not fit pre-restyled (2004–2008) due to the changed shape of the fasteners.
The price of original emblems in official dealership centers ranges from 1,500 to 3,000 rubles per piece. Alternative - certified analogues from manufacturers Heko, 3D Carbon or EGR, which will cost 2–3 times less.
How to remove the old emblem from the hood: step-by-step instructions
Removing the emblem from Octavia A5 requires care so as not to damage the paintwork. In 90% of cases, the logo is attached to double-sided tape and two plastic pistons (on models before 2008). You will need:
- 🔧 Plastic paddle or pick
- 🧴 Hairdryer (construction or household)
- 🧴 Solvent for removing adhesive (e.g. WD-40 or Anti-Silikon)
- 🧤 Gloves (to avoid leaving fingerprints on the hood)
Algorithm of actions:
- Heat the emblem with a hairdryer for 2–3 minutes (temperature ~60°C). This will soften the glue and make removal easier.
- Use a plastic spatula to pry the logo off from any angle. Move gradually so as not to break the fasteners.
- If the emblem does not budge, check for the presence of caps. They need to be carefully pulled out with pliers.
- After removal, remove any remaining adhesive with solvent. Don't use acetone — it can damage the paint!
Put on gloves|Check the temperature of the hair dryer (not higher than 60°C)|Prepare solvent for glue|Secure the hood in the open position-->
⚠️ Attention: On some versions Octavia A5 (for example, RS or Scout) the emblem can be bolted on. In this case, you will need a socket wrench 10 mm.
Choosing a new emblem: original vs analogues
When purchasing a replacement from the owners Octavia A5 There are three options: original logos, certified analogues and universal logos. Each of them has pros and cons.
Let's look at the key differences:
| Emblem type | Pros | Cons | Average price |
|---|---|---|---|
| Original (ŠKODA) | Perfect Fit, Durable, Warranty Retained | High cost, long delivery | 2 000–3 000 ₽ |
| Certified analogue (Heko, EGR) | The price is 2–3 times lower, quick receipt | Chrome color may vary, less durable mount | 600–1 200 ₽ |
| Universal (AliExpress, eBay) | Cheap, wide selection of designs | Low quality materials, inaccurate dimensions | 200–800 ₽ |
🔍 Expert advice: If you choose an analogue, pay attention to the material. Quality emblems are made from ABS plastic with chrome plated, and not from cheap metal that quickly rusts.
For those who want to stand out, there are tuning emblems with a modified design (for example, a black arrow instead of a chrome one or a 3D effect). However, such options may raise questions when passing a technical inspection.
Original (ŠKODA)|Certified analogue (Heko/EGR)|Universal (from AliExpress)|Tuning (changed design)-->
Installing a new emblem: secrets of reliable fastening
Successful installation of the logo on Octavia A5 depends on three factors: proper surface preparation, choice of adhesive and positioning accuracy. Let's look at each stage in detail.
1. Preparing the hood:
- 🧼 Clean the mounting area from dust and grease with alcohol or degreaser.
- 🔍 Check that there are no traces of old glue left on the surface.
- 📏 Use masking tape to mark the edges of the new logo (this will help avoid distortions).
2. Glue selection:
For reliable fixation the following are suitable:
- 🧴 3M VHB — industrial-grade double-sided tape (withstands up to 10 kg of load).
- 🧴 Loctite 406 - cyanoacrylate adhesive for plastic and metal.
- 🧴 ABRO AS-106 — universal glue for car emblems.
3. Installation:
- Apply glue to the back of the emblem (if using tape, glue it in advance).
- Carefully apply the logo to the hood, starting from the top corner.
- Press the emblem for 30–60 seconds (for glue) or roll it with a roller (for tape).
- Do not wash the car for 24 hours to allow the adhesive to fully cure.
If the emblem is attached to the pistons, first lubricate them with silicone grease - this will make future replacement easier.
⚠️ Attention: On models Octavia A5 Scout and RS the emblem may have additional latches. Before installation, check their integrity!
Common problems with emblems and how to avoid them
Even after correct installation with emblems Octavia A5 problems may arise. Let's look at typical situations and ways to solve them.
1. The emblem falls off after a few months
Reasons:
- 🔹 Cheap glue or tape was used.
- 🔹 The surface of the hood was not degreased.
- 🔹 The emblem was installed in the cold (the glue loses its properties at temperatures below +5°C).
Solution: Remove the emblem, clean the surface, and reinstall using 3M VHB or Loctite.
2. The appearance of rust under the emblem
This is relevant for cars operated in regions with salty roads. Rust occurs due to microcracks in the paintwork under the adhesive base.
Solution:
- 🔹 Before installation, apply an anti-corrosion compound (e.g. Movi).
- 🔹 Use emblems with a rubber gasket (they are sold complete with some analogues).
3. Tarnishing or peeling of chrome
Cheap emblems are often coated not with chrome, but with chrome paint, which wears off quickly.
Solution:
- 🔹 Buy emblems marked
"chrome plated"(real chrome plating). - 🔹 To restore shine, use a chrome polish (such as Sonax Chrome Polish).
How to check the quality of chrome plating?
Rub the emblem with a cotton pad soaked in alcohol. If the paint remains on the wheel, it's fake chrome. Real chrome plating will not wear off.
Tuning emblems: ideas for individuality
If you want to give your Octavia A5 unique look, you can modify the emblem. Here are some popular options:
- 🖤 Black emblem — instead of a chrome-plated boom, a matte or glossy black one is installed. Suitable for dark colored cars.
- 🔴 Colored backlight — LEDs are built into the emblem that illuminate the logo at night (requires connection to the on-board network).
- 💎 3D logo — a volumetric boom with a “hovering” effect above the hood. Often used on tuned cars Octavia RS.
- 🏁 Sports logos — replacement of the standard emblem with a logo ŠKODA Motorsport or vRS (even if you don't have the sports version).
📌 Important: Before installing a tuning emblem, check with the traffic police to see if this will be considered a design change. In some regions you may be fined for this.
To make your own 3D logo you will need:
- 🖨️ 3D printer (or printing services).
- 🎨 Acrylic paint and varnish.
- 🔧 Glue Loctite 406 for fixation.
Ready-made templates for printing can be found on specialized forums (for example, Skoda-Club.ru or Drive2).
Where to buy an emblem for the ŠKODA Octavia A5: trusted sources
The choice of where to buy depends on your budget and quality requirements. We have collected proven options:
| Source | Pros | Cons | Average delivery time |
|---|---|---|---|
| Official ŠKODA dealer | 100% original, guaranteed | Expensive, long delivery | 3–14 days |
| Exist.ru, Autodoc.ru | Wide range of analogues, fast delivery | Risk of running into a fake | 1–5 days |
| AliExpress, eBay | Low prices, unique designs | Long delivery, low quality | 15–45 days |
| Local auto-analysis | Cheap, you can bargain | Used parts, no warranty | 1–2 days |
💡 Tip: Before purchasing on AliExpress or eBay Be sure to read reviews with photos. Pay attention to the seller's rating (must be at least 95%) and the number of sales (100+).
If you are looking for a rare emblem (for example, for Octavia A5 Combi or Laurin & Klement), try ordering it through ŠKODA Original Parts — official catalog of spare parts with delivery from Europe.
Before purchasing a disassembled emblem, check it for chips and corrosion. Even minor damage can cause the chrome to peel off after a few months.
FAQ: Answers to frequently asked questions about Octavia A5 emblems
Is it possible to paint a faded emblem instead of replacing it?
Yes, but this is a temporary solution. For painting:
- Remove the emblem and clean it of the old coating with sandpaper (
P1200). - Apply a plastic primer (eg Motip Plastik Primer).
- Paint with chrome spray paint (Krylon Chrome or Spray Max 2K Chrome).
- Apply varnish for protection.
Such repairs will extend the life of the emblem by 1–2 years.
What glue is best to use for the trunk emblem?
For the rear emblem (which is not exposed to wind loads) the following is suitable:
- 3M Scotch-Weld 77 - spray adhesive for plastic.
- Tesa Powerstrips - double-sided tape for heavy parts.
Avoid superglue (eg. moment) - it can damage the plastic of the emblem.
What should I do if a piece of paint breaks off from the hood when removing the emblem?
Don't panic! You can restore the coating like this:
- Clean the damaged area with sandpaper (
P2000). - Apply primer to match the hood color (use touch-up pencil from ŠKODA).
- Varnish and polish with paste 3M 75.
If the chip is deep, it is better to contact a body shop.
Is it possible to install the logo from Octavia A7 on A5?
No, this is impossible without modifications. Emblems Octavia A7 (2013–present) have different sizes (95×65 mm) and the shape of the fastenings. In addition, the logo on A7 flatter and will not look harmonious on A5.
How to protect your emblem from theft?
Unfortunately, the emblems ŠKODA often stolen for resale. To protect yourself:
- Use secret bolts (with non-standard head).
- Apply to the back of the logo permanent mark (for example, engraving with a VIN number).
- Install hidden alarm with a tilt sensor (it will trigger when you try to remove it).