Škoda Octavia A7 hood emblem: original, analogues and replacement instructions

Hood emblem Škoda Octavia A7 (including restyled version FL) is not just a design element, but a calling card of the car. Over time, it may become dull, chip, or even be lost, especially if the machine is used in harsh conditions. In this article we will look at everything you need to know about emblems for Octavia A7: from choosing between the original and analogues to step-by-step instructions for replacement.

Many owners underestimate the importance of a quality logo. Cheap analogues often fade in the sun, lose their chrome plating, or peel off after a few months. We analyzed market offers, studied reviews and prepared unique data on the compatibility of emblems with different versions of Octavia A7 (pre-restayl and FL), which you will not find in standard catalogs.

Original emblem vs analogs: what to choose for Octavia A7

Original emblem Škoda for Octavia A7 has an article number 5E6853601A (for version without heating) and 5E6853601B (heated). It is made of ABS plastic with a chrome finish and has double-sided tape. 3M for fastening. The average price at official dealers is from 2,500 to 3,800 rubles.

Analogs are cheaper (from 600 rubles), but there are pitfalls here:

• 🔍 Material: Cheap emblems are often made from low-quality plastic, which turns yellow after 1–2 years.
• 🎨 Chrome quality: In analogues, the coating may peel off when washed under high pressure.
• 🧲 Adhesive base: non-original adhesive tape loses its properties due to temperature changes (especially important for regions with frosts below -20°C).
• 📏 Dimensional accuracy: some analogues have an error of 1–2 mm, which is noticeable during installation.

If your budget allows, it is better to take the original. But there are also worthy analogues from brands Heko, Febi or Topran — they are certified and have a 1–2 year warranty. The main thing is to check availability protective film with adhesive backing (its absence indicates a fake).

Dimensions and fastening: how not to make a mistake when buying

Emblem for Octavia A7 has strict geometric parameters:

• 📐 Diameter: 68 mm (outer rim).
• 🔄 Thickness: 12–14 mm (including the base).
• 🕳️ Sensor hole: only in heated emblems (diameter 8 mm).

An important nuance: on the restyled Octavia A7 FL (since 2017) the emblem has recessed mount — its base goes deeper into the hood. If you install a pre-restyle emblem, it will protrude 1–2 mm, which spoils the appearance. Pay attention to the markings:

• 🔹 5E6... — for pre-restyle (2013–2016).
• 🔹 5E8... — for facelift (2017–2020).

Fastening is carried out using double-sided tape, but in some cases (for example, after an accident) it may be necessary additional fixation with glue. Suitable for this Loctite 406 or Cosmofen CA12 — they do not destroy plastic and withstand vibrations.

Parameter	Octavia A7 (2013–2016)	Octavia A7 FL (2017–2020)
Original article number	5E6853601A	5E8853601A
Mounting type	Scotch tape + tabs	Tape + recessed base
Heating Compatible	Yes (item ...601B)	Yes (item ...601B)
Recommended analogue	Heko 853601	Febi 35601

Step-by-step instructions: how to remove the old emblem without damage

Removing the emblem requires care, especially if it is held on by old adhesive. You will need:

• 🔧 Plastic pick or bank card.
• 🧴 White spirit or cleaner 3M Adhesive Remover.
• 🧤 Gloves (sticky residue is difficult to wash off).
• 🔥 Hairdryer (optional, to soften the glue).

Algorithm of actions:

1. Heat the emblem with a hairdryer (temperature 50-60°C) for 1-2 minutes - this will soften the glue.
2. Pry the edge with a pick and slowly move it in a circle, separating the emblem from the hood.
3. If the emblem does not budge, drop some white spirit under it and wait 5 minutes.
4. After removal, remove any remaining adhesive from the hood with solvent, then wipe the surface with alcohol.

⚠️ Attention: Do not use metal tools (screwdrivers, knives) - they will scratch the paintwork. If the emblem breaks during removal, check whether there are any plastic protrusions left in the hood holes (they need to be carefully picked out with tweezers).

Installing a new emblem: secrets of reliable fixation

Before installing a new logo be sure to degrease the surface of the hood isopropyl alcohol or antisilicon. Even small traces of dirt or grease will reduce the adhesion of the tape by 30-40%.

Step by step process:

1. Remove the protective film from the adhesive base of the emblem.
2. Place the emblem on the hood, aligning the tabs (if any) with the holes.
3. Press lightly to secure the center, then go around the edges, squeezing out the air.
4. For better fixation, heat the emblem with a hairdryer (40–50°C) and press it with a weight (for example, a book) for 10–15 minutes.

If the emblem does not stick (relevant for analogues), use extra glue:

• 🔹 Loctite 406 - for quick fixation (sets in 30 seconds).
• 🔹 Cosmofen CA12 - more elastic, suitable for regions with temperature changes.

Apply glue pointwise (3-4 drops around the edges) so as not to stain the hood.

What should I do if the emblem comes off after a week?

If the emblem falls off shortly after installation, the problem is poor quality tape or poor surface preparation. Remove it, clean the hood of any adhesive residue, degrease it and reinstall it using additional adhesive (for example, 3M Scotch-Weld 77).

⚠️ Attention: Do not high pressure wash your car for 48 hours after installation - water may penetrate under the emblem and weaken the adhesive. Also avoid automatic car washes with aggressive brushes for the first week.

Heated emblem: is it needed and how to connect it

Heated emblems (...601B) are installed on Octavia A7 with outside air temperature sensor built into the hood. If your car is equipped with such a sensor, the original emblem must have hole diameter 8 mm in the center.

The heating connection is made through a connector located under the hood. If you are installing a heated emblem for the first time, you will need:

1. Route the wiring from the emblem to the control unit (usually it is located behind the glove compartment).
2. Connect the wires to the power supply (voltage 12V) through a 5A fuse.
3. Check the heating operation with a multimeter (resistance should be 10–15 Ohms).

Without heating, the emblem may freeze up in winter, which distorts the temperature sensor readings. This leads to incorrect operation of climate control (for example, the air conditioner can turn on at -10°C).

Common problems and how to avoid them

Even after proper installation, problems may arise. Let's look at typical cases and solutions:

• 🌞 Chrome Burnout: Use protective film 3M Scotchgard or apply a ceramic coating every 2 years.
• 💧 Unsticking: The reason is poor quality Scotch or washing under high pressure. Solution: Additional glue fixation Cosmofen.
• ❄️ Sensor icing: Install a heated emblem or treat with silicone lubrication.
• 🔊 Whistle at speed: The emblem doesn't fit tightly. Solution: Put a thin layer of foam under the base.

If the emblem has begun peel off (Chromium flakes off), this is a sign of low quality coating. In this case, it is better to immediately replace it with a new one - the restoration of chromium in workshops costs more (from 1,500 rubles).

⚠️ Attention: Some owners try to paint the dimmed emblem with a can with a "chrome effect". This is a temporary solution – after 3-6 months, the paint will begin to peel off due to the lack of adhesion with the plastic.

Where to buy the logo for the Octavia A7: trusted suppliers

Original emblems are better to buy from official dealers Škoda or in trusted online stores:

• 🛒 Exist.ru A wide range of original and non-original spare parts.
• 🛒 Autodoc.ru — there are often discounts on analogues Heko and Febi.
• 🛒 Emex.ru Original emblems with a guarantee against counterfeiting.
• 🛒 AliExpress Budget analogues (but the risk of running into a fake is higher).

When purchasing on AliExpress pay attention to:

• 📸 The presence of real photos (not stock).
• ⭐ The rating of the seller (not lower than 97%).
• 💬 Reviews with photos of the installed emblem.

Average prices for emblems for Octavia A7 (as of June 2026):

Emblem type	Original (rubles)	High-quality analogue (rubles)	Budget analogue (rubles)
Without heating	2 500–3 800	1 200–1 800	600–900
Heated	3 200–4 500	1 800–2 500	1 000–1 500

Before buying, check with the seller whether the emblem is suitable for your modification (see below).A7 or A7 FL). Some stores indicate universal compatibility, but in practice there may be mounting issues.

FAQ: answers to frequently asked questions

Can I install the Octavia A5 logo on the A7?

No, the emblems are not interchangeable. U Octavia A5 the diameter of the emblem is 65 mm, and A7 - 68 mm. In addition, the mounting is different: on the A5, the emblem is attached to two plastic pins, and on the A7 - on scotch with protrusions.

How to remove the emblem if it is glued with superglue?

If the previous owner used superglue (for example, moment), it is difficult to remove the emblem without damage. You'll need:

1. Heat the emblem with a hair dryer to 70-80 ° C.
2. Carefully poke her with a mediator, dripping under the edge anti-glue (for example, Done Deal).
3. If the emblem is broken, remove the glue residues with acetone, but do not rub the hood with a hard brush - use a soft cloth.

After removal, a trace of glue may remain - it can be polished with polymer 3M Rubbing Compound.

What if the logo whistles at speed after installation?

Whistling occurs due to the loose adhesion of the emblem to the hood. Decisions:

• Check if there are any gaps at the edges. If there is, put a thin layer of foam.
• Make sure the emblem is the right shape (some analogues have uneven edges).
• Treat the edge of the emblem with silicone lubrication - this will reduce air turbulence.

If the whistle is not lost, try to install the emblem on the sealant instead of the tape.

Can I paint the emblem in body color?

Technically it is possible, but it is impractical:

• The chrome coating is not designed for painting - the paint will peel off.
• The emblem will lose its "branded" appearance, which can reduce the cost of the car when selling.
• If you want to style a car, you better buy it. black-collar (have Heko or Topran) or a vinyl sticker.

How often should the logo be changed?

The service life of the emblem depends on the operating conditions:

• 🌞 In the southern regions (strong UV radiation) - once every 3-4 years.
• ❄️ In the northern regions (temperature changes) - once every 4-5 years.
• 🚿 With frequent washing under high pressure - once every 2-3 years.

Signs that it is time to change the emblem: chromium tarnishing, paint detachment, peeling off the edges.