Seat memory function in Ε KODA Kodiaq One of the comforts you will appreciate from the first days of operation. Especially if the car is used by several people with different landing preferences. The system allows you to save up to three individual profiles (depending on the configuration), including the position of the seat, steering column, mirrors and even climatic settings. But how to use it, so as not to waste time on manual adjustment every time?

In this article we will analyze all setup steps From basic position preservation to the subtleties of key synchronization and solving typical problems. Relevant to Kodiaq 2017–2026 release (including restyled versions), but some nuances may differ depending on the configuration (Ambition, Style, Sportline, L&K) and year of production. If your car is equipped virtual key or system Keyless, pay attention to additional sections.

Which settings are saved in the seat memory?

Memory system in Kodiaq remembers not only the position of the driver's seat. Depending on the configuration, the profile may include:

  • πŸͺ‘ Driver's seat position (longitudinal, height, backrest tilt, lumbar support)
  • πŸš— Steering column (height and reach if electrically adjustable)
  • πŸͺž Side mirrors (tilt angle, folding/unfolding)
  • 🌑️ Climate settings (temperature, air distribution, blowing intensity) - only in top-end configurations
  • πŸ”‘ Binding to the ignition key (automatic recovery when unlocked)

In basic versions (for example, Active) only the seat and mirror memory can be accessed. To check which features your Kodiaq, look into Settings β†’ Comfort β†’ Memory of the seats or contact user manual (Section "Individual settings").

⚠️ Attention: If your vehicle is installed pneumatic seats with massage (optional for L&K), their settings are not saved in the profile memory. You will have to manually adjust after each engine start.
Equipment Seat memory Mirror memory Memory of the steering wheel Key binding
Active, Ambition (base) βœ… βœ… ❌ ❌
Style, Sportline βœ… βœ… βœ… βœ… (optional)
L&K βœ… (included). lumbar support) βœ… (with autofolding) βœ… βœ…

Preparing for setup: what you need to do in advance

Before you save a profile, make sure that:

  1. The car is standing on flat surface (The tilt may distort the stored parameters).
  2. Doors closed, engine. run-up (or ignition switched on) ON).
  3. All seat adjustments, steering wheel and mirrors are complete manually (The electric drives must be active).
  4. The key to which the profile will be attached is in the salon (if the function is used) Keyless).

If in your Kodiaq system installed Virtual CockpitCheck that the display settings (Menu β†’ View β†’ Individual View) the desired display parameters are selected. They are not saved in the memory of the seats, but can be reset when changing the profile.

πŸ“Š How often do you use your car’s seat memory?
  • Every day
  • Several times a week
  • Less than once a month.
  • Never used it
  • No such function

Step-by-step instructions: how to save your profile

The algorithm for saving settings is the same for most configurations KodiaqIt may vary slightly depending on the year of release. Follow this instruction:

  1. Take a comfortable position in the driver's seat. Adjust:
    • πŸ”„ Longitudinal position (lever under the seat or buttons on the door)
    • ↕️ Back height and inclination (buttons on the side panel of the seat)
    • 🦴 Lumbar support (if available)
    • πŸͺž Rearview mirrors (rear view select button + joystick on the door)
    • πŸš— Steering column (lever under the steering wheel or electric drive)
  • Click the button M (Memory) on the driver's door. It is located next to the mirror regulators. Hold her down. 3–5 secondsuntil a beep sounds.
  • Select a profile number (1, 2 or 3) buttons 1, 2 or 3 It's on the same panel. Repeated press confirms the preservation.
  • Wait for the second beep. This means that the settings have been successfully saved.

    • If your vehicle is provided in your vehicle key-bindingAfter saving the profile:

    1. Turn off the ignition and remove the key.
    2. Insert the key to which you want to link the profile and turn on the ignition (ON).
    3. Press and hold the button M + profile number button (S)1, 2 or 3) during 10 secondsUntil there's a long signal.

    Adjusted seat height | Backrest tilt checked | Mirrors tuned to your height | The steering wheel adjusted to offset and height | Engine on (or ignition in ON position)->

    ⚠️ Attention: If, after saving the mirror profile, automatically folding/folding When blocking/unlocking, this means that the function is enabled in the settings. Auto-folding of mirrors (Settings β†’ Comfort β†’ Mirrors). You can turn it off if it's in the way.

    How to restore a saved profile

    Resetting the settings can occur automatically (key binding) or manually. Let's consider both options.

    Automatic recovery (key binding)

    If you have properly linked the profile to the key, the settings will be restored when:

    • πŸ”‘ Unlocking the car from the key fob (for systems) Keyless).
    • πŸš— Turning on the ignition (if the key is inserted into the lock).

    The process takes 2–3 seconds. If the seat or mirrors are not moving, check:

    • πŸ”‹ Battery level (at low charge, electric drives may not work).
    • πŸ”§ Menu settings Settings β†’ Comfort β†’ Seat Memory β†’ Autorecovery.

    Manual recovery

    If automatic recovery is not configured or not working, use the buttons on the door:

    1. Turn on the ignition (ON).
    2. Click the button M and, holding it, select the profile number (1, 2 or 3).
    3. Release the buttons and the settings will begin to recover.
    πŸ’‘

    If the profile is not restored, try it. save He's back. Sometimes the failure occurs due to temporary errors in the electronics, especially after the battery is turned off.

    Typical problems and their solutions

    Even in a car as reliable as Ε KODA KodiaqThere may be problems with the seat memory. Let’s take a look at the most common ones:

    Problem 1: The profile is not saved

    Causes and solutions:

    • πŸ”‹ Weak battery Electrical drives require sufficient voltage. Check the charge or recharge the battery.
    • πŸ› οΈ Button malfunction M Try to clear your contacts or contact the service.
    • πŸ“± Control unit failure Sometimes it helps to reset the settings to the factory (Settings β†’ System β†’ Reset).

    Problem 2: The seat moves in jerks or not to the end

    This may be due to:

    • 🧹 Pollution of guides Clean them of dust and lubricate them with silicone lubricant.
    • πŸ”Œ Oxidation of contacts in the electric drive connectors. Diagnostics are required.
    • βš™οΈ mechanical wear If the seat "sinks" during recovery, it may be necessary to replace the gears of the drive.

    Problem 3: Settings are reset after the battery is turned off

    B Ε KODA Kodiaq The memory of the seats is non-volatile, but with complete de-energization (for example, when replacing the battery), the profiles can be reset. To avoid this, use it. external power supply (Power Bank for Auto) when working with wiring.

    What to do if the profile is linked to a lost key?

    If the key is lost and the profile is tied to it, you will have to reprogram the seat memory via the diagnostic connector. This can be done in the official service Ε KODA or by means of a car scanner (e.g., VCDS or OBDeleven). It is impossible to reset the binding without equipment.

    Additional functions: what else can be configured

    In top trim levels Kodiaq (for example, L&K) extended memory options are available:

    • 🌬️ Climate profiles - preservation of temperature, direction of blowing and intensity of ventilation.
    • πŸ”Š Audio settings Volume, sound balance and favorite radio stations (only in systems) Amundsen and Columbus).
    • πŸ“± Synchronization with phone - automatic connection Bluetooth Starting your favorite apps (requires) Ε KODA Connect).

    To enable these features:

    1. Go to Settings β†’ Comfort β†’ Memory of the seats β†’ Additional.
    2. Check the necessary options (for example, Climate control or Multimedia).
    3. Save the profile again (as described above).

    Please note: if the vehicle has a system installed Virtual CockpitSome display settings (for example, dashboard) are not saved profile. They will have to be set up separately.

    πŸ’‘

    Available with Keyless and Virtual Cockpit When changing the profile, it can be dropped widgeting on screen. This is normal behavior – the manufacturer did not provide for their preservation.

    Operating tips: how to extend the life of mechanisms

    To keep your seat memory running smoothly for years, follow these guidelines:

    • πŸ›‘ Don't press the memory buttons while moving the seat or mirrors - this can cause the electric drive to fail.
    • 🧴 Lubricate the guides regularly seats (1-2 times a year) with silicone lubricant.
    • ❄️ In winter beforehand let the car warm up for 2-3 minutes - this will reduce the load on the electric drives.
    • πŸ”§ If you notice extraneous sounds (creaking, knocking) when adjusting, contact the service - this may be the first sign of wear mechanisms.

    If you often carry oversized cargo and fold the rear seats, check if they interfere with the driving-chair. In some cases, this can block the memory.

    FAQ: answers to frequently asked questions

    Is it possible to transfer memory profiles from one Kodiaq to another?

    No, memory profiles are stored in the control unit of the specific vehicle and are not transferred. However, in some trim levels (with Ε KODA Connect) can be synchronized some settings (e.g. climate or multimedia) via cloud, but not seat position.

    How many profiles can I save?

    In most trim levels Kodiaq available 3 profiles. In basic versions (Active) there can only be 1–2. Please check the instruction manual for exact information.

    Why are the memory settings reset after washing the car?

    Most likely, water got into the electric drive connectors or control unit. This may cause a short circuit and reset. It is recommended to avoid directing a jet of water at doorways and check the seals.

    Is it possible to turn off the sound when saving a profile?

    Yes, in some trim levels this can be done through the menu Settings β†’ Sounds β†’ Confirmation tones. However, the audible alert helps you understand that the settings have been successfully saved, so it is not recommended to turn it off.

    Does the seat memory work when the car is towed?

    No, when towing (when the engine is off) electric drives not active. To restore the profile, you must turn on the ignition (ON) or start the engine.