Crossover owners Skoda Yeti Often, they need to repair the back door. Whether it's a replacement for a broken one. castle, elimination of creaks, replacement seal or transfer wiring, to perform these works requires dismantling of the inner lining. The process is not super complicated, but requires accuracy, since plastic is not very complex. Yeti It can be fragile at low temperatures, and the mounts have a specific design.

Incorrect removal of the panel can lead to breakage of the clip, the appearance of gaps or damage to decorative linings. In this article, we will discuss in detail how to remove correctly plastic panel The trunk door without damaging the body structure. We will look at all the nuances of working with screws, latches and electric connectors so that you can complete the task yourself.

Preparing tools and workspace

Before starting the dismantling, all the necessary tools must be prepared. Lack of the right inventory can force you to use brute force, which is fraught with breakdown of fragile elements of the interior. Skoda Yeti. You will need a set of screwdrivers, including cross and flat, as well as a specialized tool for removing the skin.

The workplace should be well lit and cleaned of unnecessary items. It is recommended to spread soft fabric or cardboard on the floor so that in case of falling parts they do not get scratched and lost. It is important to have a small fastener container on hand, as many screws and fixers are used in the door.

  • πŸ› οΈ Plastic spatula (or wide screwdriver wrapped with tape) for tweaking clips
  • πŸ”§ Set of cross screwdrivers (PH2, PH3) for screw twisting
  • πŸ’‘ Bright flashlight for viewing hard-to-reach places behind the panel
  • 🧀 Gloves to protect hands from sharp edges of metal and plastic

Pay special attention to the condition plastic clips. If they are old and brittle, it is better to immediately purchase a set of spares, since when dismantled, some of them will inevitably break. This is standard practice in the repair of VAG-group cars, including: Skoda Yeti.

⚠️ Warning: Never try to tamper with a metal screwdriver without protection! The sharp edges of the metal will instantly leave deep scratches on the plastic panel that cannot be removed by polishing.

Removal of decorative elements and access to fasteners

The first step is to remove visible decorative linings, behind which the main fasteners hide. On the trunk door. Skoda Yeti This often includes an opening handle and a lock lining. These elements are held on plastic latches or screws hidden under the caps.

First, remove the rubber seal from the top of the door if it interferes with access to the screws. Then gently tuck the boot opening handle lining. It is mounted on several clips, which must be carefully decomposed, leading the tool around the perimeter of the part.

After removing the lining, you will see screws that fasten the mechanism of the handle. They need to be removed, but not completely removed, so as not to lose. Next, remove the decorative stub in the area of the castle, if it is present in your configuration. Often there is a screw hidden, fixing itself. lock mechanism.

  • πŸ” Inspect all joints of panels for the presence of hidden screws under decorative caps
  • πŸ”© Do not put excessive effort when removing the lining of the handle, so as not to break the plastic ears.
  • πŸ“¦ Immediately remove the removed screws in a separate compartment so that they do not fall into the door cavity.

β˜‘οΈ Removal of decorative elements

Done: 0 / 4

In some trim levels Skoda Yeti There may be additional noise insulation or a speaker, which must also be gently disconnected before the panel is completely removed. If the speaker is connected through the connector, just click its lock.

Sometimes screws can be hidden under rubber plugs at the bottom of the door. Conduct a thorough inspection of the entire perimeter of the panel. Missing even one screw will lead to the fact that when you try to remove the panel will crack at the fixation point.

If the screw is very rusty or boiled, do not try to rip it off immediately. Treat the connection site with penetrating lubricant (such as WD-40) and let it stand for 10-15 minutes. Use a screwdriver with a perfect fit of a stinger, so as not to lick the slime.

Dismantling of the interior panel

When all visible screws are removed and decorative elements removed, the most important moment comes - the removal of the panel itself. It is held on the door by a system of plastic clips that are inserted into the holes around the perimeter. These clips have a spacer mechanism that must be carefully compressed or tampered with.

Start the process at the bottom of the door. Insert a plastic spatula between the panel and the metal of the door in the place where you think the clip is. Smoothly, but with effort pull the panel on yourself. You will hear a characteristic click - this means that the clip has left the hook.

Move along the perimeter of the door, sequentially releasing clips. Do this evenly, without trying to bend a large piece of the panel at once, as this can lead to its fracture. Exercise special care in corners and around handles where the plastic is thinner.

  • 🚫 Do not pull the panel sharply upwards, so as not to break the pins of the glass mounting or the mechanisms of the window lifter.
  • πŸ”§ If the clip does not lend itself, check if there is a discreet screw somewhere.
  • πŸ“ After releasing the clips, lift the panel up to remove it from the guides of the lock.

Door assembly and final check

Assembly is carried out in reverse order. First you need to install the lock mechanism in place and connect the rods to it. Make sure that the cables fit into their grooves until you hear a characteristic click. Then bolt the lock to the body.

Next, connect the electrical connectors. The wires must be carefully laid so that they do not interfere with the movement of the panel and are not pinched. Check that the wiring corrugation does not get under the panel clips.

Before installing the panel itself, check the condition of all clips. If some are broken, replace them with new ones. Insert the clips into the panel holes until they are ready to snap into place. Carefully place the panel on the door, aligning it with the lock guides.

Start pressing the panel around the perimeter, starting from the center and moving towards the edges. Do you hear clicks? Great, that means the clips are in place. Make sure the panel fits snugly and has no gaps. Reinstall all the screws you removed earlier.

  • πŸ”© Tighten the screws with moderate force to avoid stripping the threads in the plastic.
  • 🧹 Check that the door seal lies flat and is not twisted.
  • πŸšͺ Open and close the door several times to ensure the lock is working correctly.

Finally, install decorative trims and handles. Check the operation of all buttons and lights. If everything works properly and there are no extraneous squeaks when closing the door, the work is completed. Yours Skoda Yeti ready for use again.