Crossover owners Skoda Yeti Often face the need to replace wipers, especially in the off-season, when rubber elements tan from the cold or damaged by reagents. The removal procedure seems trivial, but the specific design of the levers on this model requires special care not to bend the metal and break the glass.
Incorrect actions can cause the spring of the lever to work with excessive force and hit the windshield. In this article, we will analyze the step-by-step dismantling algorithm, discuss the nuances of fixation in the service position and consider the mistakes that even experienced motorists make.
Preparing the car and tools for work
Before you start physical impact on the nodes of the wiper, it is necessary to prepare the working space. You wonβt need a complex set of tools to work, but having several items will greatly simplify the process and protect glass.
You will need a soft cloth or an old towel that you need to put on the glass under the janitor's lever. This is critically important, as if the lever is accidentally released, it can hit the windshield, leading to cracks or chips. Also prepare a flat screwdriver with a soft tip if you need to remove the plastic lining at the base.
Make sure the car is on a flat surface and the engine is silenced. If you plan to change brushes on both sides, start with the driverβs side, as it is usually longer and requires a more careful approach.
Moving the wipers to the service position
In many modern cars, including Skoda YetiThere is a function of "service position" or "service position". This allows you to raise the levers of the wiper so that they do not interfere with the replacement and do not press against the glass with springs during operation.
To activate this mode, turn on the ignition, but do not start the engine. Then turn on the wipers and turn them off immediately within two seconds of stopping. For the next 30 seconds, press and hold the wiper lever up or down (depending on the modification) until the brushes are upright.
If your model does not support automatic transition, you will have to act manually. Raise the lever manually to the end of the glass. Here it is important to remember about a strong spring: once you release the lever, it can suddenly return to its original position. Be prepared to hold him.
In the service position, you will get access to the brush mount. Note that some modifications may have different types of attachments: hook, side pin or specific lock.
- Once a year
- Once every six months
- Only when they stop cleaning
- I don't know the exact date
Algorithm for removing the wiper blade
The process of dismantling depends on the type of fastening installed on your Skoda Yeti. Most often there is a system of fastening of the type "hook" (hook) or a specific bracket characteristic of the VAG group. The algorithm of actions requires precision and confidence.
After the lever is raised and fixed, find the lock on the body of the brush. Usually it is a plastic button or tongue located at the connection of the metal lever and the plastic fittings of the janitor. Press this lock and simultaneously pull the brush downwards towards the glass to release it from the grip.
If you have an original mounting system, you may need to first remove the plastic casing that covers the mechanism. To do this, gently tuck it with a flat screwdriver and remove it. After that, you will see the snatching mechanism itself.
Do not use excessive force. If the brush fails, check if you have completely released the lock. Damage to plastic latches can cause the new brush to hold poorly and rattle when moving.
βοΈ Check before removal
Design features and types of fastenings
Owners Skoda Yeti You may encounter different types of adapters, as different wiper suppliers were used in different configurations. The most common is the universal hook, which fits most European cars.
However, there are specific systems where the brush is put on the lever from above and fixed by the button on the side. In such cases, you need to squeeze the side button and move the brush along the lever. Sometimes it is necessary to remove a small plastic cap covering the mount before reaching the retainer.
It is important to consider the length of the levers: on the driverβs side it is usually 600 mm, and on the passenger side it is 400 mm or 475 mm. Incorrect selection of length can lead to the fact that the wipers will beat each other or will not clean the entire area of glass.
What to do if the latch is broken?
If the plastic fixture is broken, you can use a trick: carefully wrap the attachment place with tape or tape to create a temporary fixation, but it is best to replace the entire lever or contact the service, as the reliability of the attachment will be compromised.
Compatibility and Size Chart
For the correct replacement, you need to know the exact sizes of the brushes that are suitable for your model. Below is a table with recommended parameters for different years of release. Skoda Yeti.
| Year of issue | Driver side(mm) | Passenger side (mm) | Mounting type |
|---|---|---|---|
| 2010-2013 | 600 | 400 | Hook |
| 2014-2017 | 600 | 475 | Side pin/Hook |
| 2018-2019 | 600 | 475 | Specific lock |
| All years | Secondary (back) | 380-400 | Pin (Pin) |
Note that the rear wiper has a completely different mount, often referred to as a βpin.β Replacing it also requires care, as the rear windshield wiper lever also has a powerful spring.
When buying new brushes, always check the labeling on the package. Manufacturers often specify not only the length, but also the type of adapter included in the kit. Universal adapters may not fit specific levers Skoda Yeti.
β οΈ Attention: Never turn on the wipers if they are removed or in an unnatural position without blades. This will cause rapid wear on the trapezoid mechanism and may burn out the wiper motor.
Before buying new brushes, take a photo of the old ones and show the photo to the consultant in the store - this will help to avoid mistakes with the type of fastening.
Installing new brushes and checking operation
After you have removed the old elements, installing the new ones occurs in the reverse order. Slide the new brush onto the lever until you hear the characteristic click of the latch. Make sure it fits snugly and has no play.
Carefully lower the lever onto the glass. Do this slowly, controlling the moment you touch the glass. If you use the method without a service position, hold the lever with your hand until it touches so that the spring does not hit the glass.
After installation, turn on the wipers and test their operation on dry and wet glass. Observe the trajectory of movement: the brushes should not hit each other, and should not leave unwashed stripes or streaks.
If you feel vibration or hear unusual sounds, check that the adapters are installed correctly. You may have not fully latched the latch or selected the wrong adapter from the kit.
Correct installation of the clamp is confirmed by a clear click and the absence of play when rocking the brush by hand.
Common mistakes and how to avoid them
One of the most common mistakes is trying to remove the brush without raising the lever to the vertical position. This makes it impossible to access the fastener and increases the risk of damage to the paintwork on the hood.
Another problem is using excessive force during removal. The plastic fastening elements are quite fragile, especially after several years of use in the sun and frost. If the latch does not budge, try shaking the brush slightly without releasing the button.
Sometimes car owners forget about the plastic cover at the base of the lever. If not removed, it may prevent the arm from lifting completely or interfere with the installation of a new brush.
Also worth mentioning is the wrong side installation error. Sometimes adapters can be put on mirror-like, which will lead to an incorrect angle of contact between the rubber and the glass and poor cleaning.
β οΈ Attention: Do not leave the windshield wiper arms raised for a long time after replacement. Strong winds can rip them off and hit the glass, even if you haven't touched them.
Why do wipers squeak?
The squeak can be caused not only by wear of the rubber, but also by contamination of the glass or the lever itself. Try wiping the glass with an alcohol wipe and lubricating the arm joints with silicone grease.
Maintenance and life extension
To make your wipers last longer, regularly clean them of dust, sand and reagents. In winter, be sure to clear the tires of ice before turning them on, as dry work on ice quickly damages them.
Use a special glass cleaner, not regular water. Water can leave a residue that will clog the pores of the rubber and reduce its elasticity. Also avoid using harsh detergents when cleaning glass.
Check the condition of the lever springs. Over time, they may weaken and the pressure on the glass will be insufficient. This will cause the wipers to leave streaks even on new blades.
Regular cleaning of glass and rubber brushes from dirt extends the life of both components and improves visibility.
Conclusion
Replacing wipers with Skoda Yeti - This is a procedure that you can perform yourself, saving money on the service. The main thing is to be careful when working with spring mechanisms and strictly follow the instructions for removal and installation.
Remember that proper operation of your windshield wipers is critical to driving safely in bad weather. Don't put off replacement until the last minute if you see that the old brushes can no longer clean the glass.
By following these recommendations, you can quickly and safely upgrade your car's glass cleaning system, ensuring you have excellent visibility on the road at any time of the year.
Keep spare brushes in the trunk of your car, especially in winter, so that you can always replace them in case of sudden failure.
Is it possible to remove the wipers without moving them to the service position?
Yes, you can, but it requires special care. You will have to manually hold the lever up while you remove the wiper to prevent the spring from hitting the glass.
What size wipers are suitable for Skoda Yeti?
Standard dimensions for most models: 600 mm for the driver's side and 400-475 mm for the passenger side. The exact size depends on the year of manufacture and configuration.
What to do if the new brush does not fit the mount?
Check the adapter kit. Often the problem is that the wrong adapter from the kit is installed. Try other options or use a universal adapter.
How often should wipers be changed?
It is recommended to change the brushes every 6-12 months, or sooner if they leave streaks, squeak or do not clean the glass well.
Do the wiper joints need to be lubricated?
Yes, periodically lubricating the hinges with silicone grease helps maintain smooth operation and extends the life of the mechanism.