Removing the front bumper on a Škoda Yeti: instructions with photos and secrets of the masters

Removing the front bumper Škoda Yeti - a task that every owner of this crossover faces sooner or later. Whether you are planning to paint after an accident, install foglights, replace the radiator grille or simply diagnose hidden damage, knowing the correct sequence of actions will save time and nerves. Unlike many modern cars, where the bumper is attached to dozens of hidden clips, Yeti design is relatively simple, but has its pitfalls - especially in the areas of attachment to the fender liners and the front beam.

This article is suitable for owners Yeti first generation (2009–2017) regardless of configuration. We will analyze two scenarios: partial dismantling (for example, to replace PTF) and complete removal of the bumper with all fastenings disconnected. You will also learn which tools are really necessary, and which you can do without, and how to avoid common mistakes that lead to broken clips or damage to the paintwork.

Preparation: tools and working conditions

Before you begin dismantling, make sure you have everything you need. Minimum set of tools to remove the bumper Yeti includes:

• 🔧 Socket wrench or socket 10 mm (for mounting bolts to the subframe)
• 🔧 Phillips and flathead screwdrivers (for self-tapping screws and clips)
• 🔧 Plastic mounting spatulas or picks (to avoid damaging the latches)
• 🔧 Pliers or pliers (for hard-to-reach clips)
• 🔧 Flashlight or head light (underhood lighting)

If you are planning complete dismantling, additionally prepare:

• 📦 Containers for small parts (bolts, clips, pistons)
• 🧴 Silicone grease or WD-40 (for rusted fasteners)
• 🎨 Painting tape (to avoid scratching the body when removing)

It is better to do the work in dry, well-lit place - garage or box. If you have to remove the bumper on the street, choose a day without wind or precipitation: dust and moisture can get on the elements exposed after dismantling (for example, a radiator or headlights). Also note that on Yeti with DSG or all-wheel drive 4x4 It may be necessary to remove the crankcase guard to access the lower bolts.

Step-by-step instructions: how to remove the front bumper

The dismantling process is conventionally divided into 4 stages: preparation, removal of the upper fasteners, detachment of the lower fasteners and final separation of the bumper. Let's start with the most important thing - car blackout.

⚠️ Attention: Before starting work Be sure to remove the negative terminal from the battery. On Yeti with xenon headlights or LED optics, this will prevent a short circuit if the wiring is accidentally touched. Also, do not forget that after disconnecting the battery, the memory of the radio and on-board computer may be reset (check the access codes in advance!).

Step 1. Removing the front license plate and radiator grille

1. Unscrew 4 screws license plate mounts (they are hidden under plastic plugs).
2. Remove the license plate and set it aside.
3. Pry up the plastic radiator grille Yeti using a spatula (it is attached to 4 clips - two on top and two on the sides).
4. Disconnect the power connector of the temperature sensor (if it is in your configuration).

Step 2. Untwisting of the top bolts

Under the hood you'll see 2 bolts 10 mm (one on each side) that attaches the bumper to the spars. There is also 2 plastic pistons in the upper part of the bumper - they need to be carefully pulled with pliers or a screwdriver. Do not make excessive efforts: Yeti These pistons often break down at the first dismantling.

Is the battery terminal disconnected|

Removed license plate and radiator grille |

Are there any spare clips in case of breakdown?

Is the rod under the bumper (so as not to scratch the hood)-->

Step 3. Removal of lower anchorages and under-plates

This is where the main difficulties begin. Bumper Yeti mount 3 bolts on each side (two front and one side). To get to them:

1. Turn the wheels to the extreme position (for example, to the left to access the right wing).
2. Remove plastic clips mounting the wing to the bumper (usually 4-5 pieces).
3. Unscrew the bumper mount bolts to the underwing (a key extension cord may be required).
4. Repeat the procedure for the second side.

Step 4. Disconnection of the bumper from the body

After all the bolts and clips are removed, the bumper should "step away" from the body. But, Yeti there is more 2 hidden fixers at the bottom (under the radiator). To disconnect them:

• 🔹 Gently pull the bumper towards you, starting from one of the corners.
• 🔹 If the bumper "bitten", check if there are untwisted bolts in the area of fog lamps.
• 🔹 For convenience, ask the assistant to hold the bumper while you unplug the last clips.

After the bumper is completely separated, place it on a soft surface (for example, cardboard) with the front side upwards so as not to damage the paint coating.

Common mistakes and how to avoid them

Even experienced car owners sometimes make mistakes when removing the bumper. Yetiwhich lead to additional costs. Here are the most common of them:

Error	Consequences	How to avoid
Using metal tools to remove clips	Scratches on plastic, broken latches	Use only plastic blades or wrap the screwdriver with insulation
Neglect of battery terminal removal	Short circuit, reset electronics settings	Always turn off the “minus” before working with wiring
Strong pulling force when "bite" bumper	Cracks in plastic, broken anchorages	Check all bolts and clips, use lubricant for rusty elements
Loss or confusion of clips during assembly	Bumper rattling, loose fitting	Stacking parts in signed containers or packages

Critical error: attempt to remove the bumper without removing the underwings. On Yeti, this will lead to deformation of plastic mounts and require their replacement (the cost of the clip kit is from 800 to 1500 rubles).

One more nuance - fog-wiring. If you do not disconnect the connectors before removing the bumper, there is a risk of breaking the wires. Nana Yeti With the rear PTF (in the bumper), this is especially true: connectors often “stick” and require careful handling.

Partial dismantling: if you only need to remove a part of the bumper

It is not always necessary to remove the bumper completely. For example, to replace fog lights, the sensor of the parktronic or radiator grille is enough to disconnect only part of the mounts. Let's look at two scenarios:

1. Replacement of fog lamp (PTF)

• 🔦 Unscrew 2 screws PTF fastenings (they are located at the bottom of the bumper).
• 🔦 Disconnect the power connector (press the lock and pull down).
• 🔦 Pull the headlight out of the groove by pulling it on you.

2. Dismantling of radiator grille

• 🔧 Remove the license plate (as described above).
• 🔧 Put the bar on the side with a plastic spatula (it is held on the 4 clips).
• 🔧 If the grille fails, check if it's caught on the hood lock.

For these works, you do not need to remove the bumper completely, but be careful: Yeti with bi-xenon headlights The grille of the radiator can be attached with an additional bolt on top (under the hood).

What should I do if the clip breaks during removal?

If the plastic clip cracked or crumbled, do not try to assemble the bumper without replacing it - this will lead to rattling on the bumps. Buy a remake of the clip for Škoda Yeti (article) 1J6 807 251 for upper anchorages and 1J6 807 252 for the lower ones. A temporary solution may be the use of nylon screeds, but this does not guarantee a tight fit.

Assembly: how to install the bumper back

Installing the bumper on Yeti It often raises more questions than demolition. The main rule is: Start with the top brackets. and move down. Here is a step-by-step algorithm:

1. Make sure all clips and bolts are in place (see para. checklist at the beginning of the article).
2. Connect the bumper to the upper mounts on the spars (bolts on the 10 mm).
3. Fix the side parts of the bumper on the underwings, starting with the front bolts.
4. Install the bottom clips under the radiator (will require an assistant for alignment).
5. Connect the PTF connectors and sensors (if disconnected).
6. Set a radiator grille and license plate.
7. Connect the battery and check the operation of all systems (lighting, parking sensors).

After assembly be sure to check:

• 🔍 The gaps between the bumper and the fenders (should be the same on both sides).
• 🔍 The work of fog guards and parking sensors.
• 🔍 No rattling when passing irregularities.

⚠️ Attention: If after installation the bumper "walks" or fits loosely, the problem is most likely in the misplaced clips. Check their location again, on Yeti The top and bottom mount clips differ in shape!

Tips for caring for the bumper after the removal

If you have removed the bumper for painting or polishing, take advantage of the moment to carry out prevention:

• 🧼 Clean the inside of the bumper from dirt and salt (especially important for the winter period).
• 🔧 Check status radiator Air conditioner condenser – they often rust and require replacement.
• 🎨 Apply anti-gravel protection Vulnerable areas (lower edges, corners).
• 🔦 Examine the wiring of PTF and parktronics for grated insulation.

Use the inside of the bumper to wash the inside softbrush and autoshampoo Abrasive detergents can damage plastic. If there are chips on the bumper, treat them. primer before painting to avoid corrosion.

FAQ: answers to frequently asked questions

How long does it take to remove the bumper on the Škoda Yeti?

With experience and help, 40–60 minutes. If you’re doing it for the first time, stock up on 1.5-2 hours (especially if the clips are rusted or parts need to be replaced).

Can I remove the bumper on Yeti without a hole or lift?

Yeah, but it's less convenient. You will have to work lying under the car, which makes it difficult to access the bottom bolts. If there is no hole, use it. jack and insurance stands to lift the front of the car.

Which clips are most often broken when dismantled?

On Yeti this is top-plastics (article 1J6 807 251) and bottom clips under the radiator (article N 908 132 01). We recommend buying them in advance.

Do I need to remove the headlights to remove the bumper?

No, on Škoda Yeti You don't have to take off the headlights. However, if you plan to replace or adjust them, it is more convenient to do so with the bumper removed.

What should I do if the bumper squeaks after installation?

Creaking usually occurs due to:

• 🔹 The slender sleeves (re-install them).
• 🔹 Contact bumper with radiator (check gaps).
• 🔹 Wearing rubber seals (replacement required).

Treat problem areas silicone grease (don't use WD-40 - it dries out!).