How to properly remove the armrest on a ŠKODA Yeti: instructions with photos and videos

Removing the armrest ŠKODA Yeti - a task that owners face when renovating the interior, replacing upholstery or installing additional equipment. Despite its apparent simplicity, the process requires caution: incorrect actions can lead to breakage of plastic latches or damage to the wiring (if the armrest is equipped with heating or backlighting). In this article we will look at step-by-step instructions for front and rear armrests, list the necessary tools and point out typical mistakes.

Models Yeti Models from 2009 to 2017 have design differences depending on the configuration. For example, in versions with leather trim, the fastenings can be hidden under decorative overlays, and in basic versions they can be fixed with standard clips. We took into account all the nuances so that the instructions are suitable for most modifications. If you are planning disassembly for cleaning, replacing bearings or installing an organizer - here you will find answers to key questions.

What tools are needed to remove the armrest?

Before starting work, prepare a set of tools. Without them, dismantling can turn into torture: plastic clips ŠKODA fragile and easy to break if pryed with a screwdriver without protection. Here is the minimum set:

• 🔧 Plastic mounting blades (2–3 pcs.) - for safely snapping off the clips. Metal tools must not be used!
• 🔨 Phillips screwdriver (size PH2) - for unscrewing the screws at the base of the armrest.
• 🔦 Flashlight or table lamp — lighting will help you see hidden latches.
• 🧲 Magnetic holder - so as not to lose small screws and clips.
• 🧴 Silicone grease (optional) - for processing guides during reassembly.

If the armrest is equipped electrical functions (heating, lighting, USB connectors), additionally prepare:

• 🔌 Multimeter - to check the integrity of the wiring after dismantling.
• 📝 Marker or stickers - to mark connectors before disconnecting.

⚠️ Attention: Do not use WD-40 or other solvents on clips! They corrode the plastic, which will lead to breakage of the fasteners during the next disassembly.

Step-by-step instructions: how to remove the front armrest

Front armrest on Yeti attached to 4 clips (two on each side) and 2 screws at the base. Dismantling algorithm:

1. Open the glove compartment and move the seat back as far as possibleto access the rear of the armrest.

2. Pry up decorative overlay on the side (driver or passenger side) with a plastic spatula. Start from the top corner - the clip is weaker there.

3. Gently pull the cover towards you until you hear a click. Repeat for the second side.

4. Unscrew two screws at the base of the armrest (they are hidden under the plugs).

5. Disconnect electrical connectors, if available (in heated or USB versions).

6. Lift the armrest up and remove it from the guides.

On models with leather trim There may be additional clips under the pads. They are easy to miss if you do not inspect the structure with a flashlight.

Move the seat back|Open the glove compartment for access|Prepare plastic shovels|Mark the location of the connectors (if there is wiring)|Check for hidden clips under the trims-->

Stage	Action	Tool	Time
1. Preparation	Move the seat, open the glove compartment	—	1–2 min
2. Removing the pads	Snap off the clips with a spatula	Plastic spatula	5–7 min
3. Unscrewing screws	Unscrew the 2 screws at the base	Phillips screwdriver PH2	2–3 min
4. Disconnect wiring	Disconnect connectors (if any)	Marker for marks	3–5 min
5. Dismantling	Remove the armrest from the guides	—	1–2 min

⚠️ Attention: On Yeti 2013–2017 armrest can be hidden 10A fuse for USB ports. When disconnecting connectors, do not pull on the wires - only on the plastic case!

Features of removing the rear armrest

Rear armrest on ŠKODA Yeti It is easier to remove than the front one, but there are some nuances here. It is attached to two plastic latches and one screw (in some trim levels). The main difficulty is access to the fastenings is blocked by the back of the rear seat. You will have to either reject it or temporarily remove it.

Algorithm of actions:

1. Lower the rear seatback (if available on your configuration).

2. Pry up decorative cover at the base of the armrest with a plastic spatula.

3. Unscrew self-tapping screw (if available) with a Phillips screwdriver.

4. Gently pull the armrest up while pressing the latches on the inside.

In versions with cup holders There may be additional clips in the armrest. Their location depends on the year of manufacture:

• 📅 2009–2012: clips on the sides, no self-tapping screw.
• 📅 2013–2017: self-tapping screw + 2 clips at the front.

What to do if the latches are broken?

If the plastic clips are cracked during dismantling, they can be replaced with similar ones from VW Golf Mk5/Mk6 (article 1K0 863 251). Universal clips with a diameter of 8 mm are also suitable. Before installing new ones, lubricate them with silicone grease for easy installation.

Common mistakes and how to avoid them

Even experienced car owners make mistakes when removing the armrest. Here are the most common:

• 🔧 Using metal tools — leads to scratches on the plastic and breakage of the clips. Always use plastic spatulas.
• 🔌 Sudden jerking of connectors - may damage contacts. Disconnect them by holding the housing, not the wires.
• 🔍 Skipping hidden clips - especially true for models with leather trim. Always check the design with a flashlight.
• 📏 Incorrect installation back — if the armrest becomes less secure, check whether the guides are bent.

Another common problem is loss of screws. B Yeti The armrest mounting screws have a non-standard length (12 mm). If you lose them, replace them with similar threaded ones M5 and a flat head.

How to disassemble an armrest for cleaning or repair

If you need clean the mechanism, replace the bearings or repair the heating, the armrest will have to be disassembled. The structure consists of:

• 🔲 Top cover (attached with 4 latches).
• 🔄 Height adjustment mechanism (bearings are built into it).
• 🔥 heating element (in heated versions).

Disassembly order:

1. Remove the armrest from the vehicle (as described above).

2. Turn it over and unscrew it 4 screws on the bottom cover.

3. Carefully separate the halves, starting from the side of the adjustment lever.

4. Remove the mechanism and clean it of old grease (use WD-40 or LIQUI MOLY Kunststoff-Pflege).

For replacement bearings (article 6202-2RS) you will need a puller. Do not try to knock them out with a hammer - this will damage the seats.

Installing the armrest back: nuances

Assembly proceeds in reverse order, but there are several critical points:

1. Before installation lubricate the guides silicone grease (not lithol!).

2. Make sure all the clips are in place — if the armrest is loose, it means one of the latches is not locked.

3. When connecting wiring, check the polarity of the connectors (especially for heating).

4. After installation check the operation of all functions: height adjustment, heating, USB ports.

If the armrest creaks after assembly, the reasons may be as follows:

• 🔊 Dirt getting into the mechanism — disassemble and clean it.
• 🔧 Loose screws - tighten the fastenings.
• 🧴 Lack of lubrication — apply it to rubbing surfaces.

FAQ: Frequently asked questions about armrest removal

Is it possible to remove the armrest without the plastic blades?

Theoretically, yes, but the risk of damaging the clips or scratching the plastic is extremely high. As a last resort, use flat screwdriver, wrapping its end with electrical tape. However, it is better to buy a set of plastic spatulas (cost from 200 rubles).

What should I do if, after removal, the armrest cannot be adjusted in height?

The reason is usually displacement of guides or bearing failure. Disassemble the mechanism, check the integrity of the parts and lubricate them. If the bearings are worn out, replace them with new ones (part number 6202-2RS).

How to remove the armrest if the clip is broken?

If the clip is cracked, but the armrest is still holding on, carefully pry it off with a screwdriver and remove the remains. Replace with a new one (suitable 1K0 863 251 from VW). If the clip is completely missing, temporarily secure the armrest with double-sided tape, but install a replacement as soon as possible.

N Is it necessary to disconnect the battery before removing the heated armrest?

No, it's only necessary disconnect the connectors before dismantling. However, if you plan to solder wires or test the circuit with a multimeter, it is better to remove the battery terminal (negative).

Where to buy spare parts for the armrest ŠKODA Yeti?

Original parts can be ordered from official dealers (clips, bearings, heating elements). Analogues are searched for Exist.ru, Autodoc or Emex. The article number is suitable for bearings 6202-2RS (cost ~150 rub/piece).