Removing the rear sofa Skoda Octavia A7 The procedure that may be required for replacement air conditionerrepair pendants or installation car audio. Unlike many competitors, this car has a seat design designed so that the owner can easily access the luggage compartment or body elements without the use of a specialized car service.
The process of withdrawal does not require a lot of experience, but has its own technical features that can not be ignored. If you act rudely, you can damage the upholstery or break plastic fixtures, which will lead to an unpleasant creak in the future. We will discuss each stage, from tool preparation to final removal of the pillow and back.
Preparing tools and workspace
Before you start, make sure you have a minimum set of tools. You'll need it. flat screwdriver with a wide sting (or a plastic blade for dismantling), Phillips screwdriver and, perhaps, socket wrench 10 mm if you need to unscrew additional bolts of the frame attachment.
Make room around the car. Open the trunk and lower the rear seat backs completely if they have a separation function. This will facilitate access to the mounting points and allow you to freely manipulate the elements of the cabin. Remove all personal items from the back seats and from the trunk so that nothing gets in the way or scratches.
- π οΈ Flathead screwdriver or plastic spatula
- π οΈ Phillips screwdriver (PH2)
- π οΈ Clean rags to protect upholstery
- π οΈ Gloves to protect hands from dirt
It is important to note that on some trim levels Octavia A7 Additional bolts can be installed hidden under decorative plugs. Check for such items before starting the action.
β οΈ Be very careful with plastic clips. They are fragile, and with improper force can crack, leaving a gap in the skin or door map.
Dismantling of the lower seat cushion
The bottom of the sofa on Skoda Octavia A7 It is attached mainly to the fixers, driven into the floor, and sometimes on hooks at the back. The easiest way to start is to raise the front edge of the pillow. Put it in. plastic spatula Or a screwdriver wrapped in a cloth under the front edge of a pillow near the threshold.
Pull the pillow up in a sharp but controlled movement. You'll hear the characteristic snap of the locks' breakaway. On most versions, it is enough to raise the center or edge to free the mounts. After the front part is snapped, you will need to pull the pillow on yourself to remove it from the hooks that hold the rear edge at the back.
If the pillow does not lend itself, check if there are bolts under the decorative lining of the threshold. In some cases, the mounts may be hidden under plastic. Carefully put the plug on and check for bolts.
- π Inspect the front edge of the pillow for the presence of hidden bolts
- π Use a cloth to avoid scratching the floor or plastic
- π Pull the pillow strictly upwards, avoiding distortions
Once you remove the bottom, you will have access to the boot floor and possible suspension elements or wiring. This is a critical stage for accessing hidden nodes.
If the fixtures sit too tight, try swaying the pillow slightly from side to side, while lifting it upwards to ease friction in the attachment.
Removing the back of the back sofa
After removing the pillow, access to the back fixing mechanisms becomes more obvious. Back on. Octavia A7 It is usually supported by two upper retainers, which are inserted into the ears on the body, and lower hooks or bolts.
Find two plastic fixtures at the top of the back. They are usually located at the edges or in the center, depending on the configuration. They need to be turned or pressed to release the grip. Often it is enough to simply pull the back on yourself at the top so that it comes out of the hook.
Check the lower back of the back. There may be bolts that need to be unscrewed, or additional hooks. If the back is divided into two parts (40:60), each part is removed separately. First, remove the smaller part if it is necessary to access the larger items.
- π§ Unscrew the bolts in the lower back (if any)
- π§ Release the upper locks by turning or pressing
- π§ Carefully remove the back without hitting the ceiling skin
Sometimes the backrest can be blocked by the seatbelt locking mechanism. Make sure all belts are free and not stretched. This could prevent a complete dismantling.
- Suspension repair
- Autosound installation
- Cleaning the trunk
- Air conditioning replacement
Features of fastening in different configurations
Depending on the year of production and level of equipment Skoda Octavia A7The design of the mounts may differ slightly. Basic versions often use only plastic fixtures, while more expensive trim levels may have additional bolt joints for increased rigidity.
For example, in versions with the system ISOFIX Access to the mounts may be limited to plastic linings. They need to be carefully removed to access the bolts. It is also worth considering that cars with all-wheel drive (4x4) may have a driveshaft, which requires caution when removing seats.
It is important to distinguish between types of fasteners: some models use βlegsβ, which simply go into the slots, others require unscrewing of bolts. If you are not sure, it is better to spend time inspecting all the mounting points than breaking the part.
β οΈ Warning: Do not attempt to remove the back by force if it does not yield. Chances are you missed the hidden bolt or didnβt fully release the lock. Look at all the corners and joints.
βοΈ Check before removal
Technical nuances and hidden bolts
Sometimes when removing seats, hidden bolts are found that attach the frame to the floor. These bolts are often under decorative plugs or in hard-to-reach places. They need to be unscrewed to completely free the seat.
Use the bolts to unscrew. socket wrench or ratchet with the appropriate head. Be careful not to break the thread. If the bolt is boiling, use penetrating lubricant and give it time to act.
You should also pay attention to the wiring that can pass under the seat. On some models, there are weight sensors or heated seats. Disconnect the connectors gently by pressing the locks rather than pulling the wires.
- π© Use the right head for bolts
- π© Apply lubricant for boiled compounds
- π© Disconnect electrical connectors with caution
If you are planning to install additional equipment, make sure that the removal of seats does not disrupt the operation of regular security systems. For example, airbag sensors can be connected through connectors under the seat.
What to do if the bolt is broken?
If the thread is broken, you can try to restore it with a meter or use a larger diameter screw. In extreme cases, drill and put the insert.
Comparison of dismantling methods
For clarity, compare the basic methods of removing seats on different models of the Volkswagen Group, which refers to the Octavia A7. This will help you to understand how unique your car is.
| Method | Difficulty | Tools | Risk of damage |
|---|---|---|---|
| Only fixers. | Low | Manual labor | Minimum |
| Bolted connections | Average | Set of keys | Medium |
| Combined | High | Keys + Screwdrivers | High |
| Electrically wiring. | High | Keys + connectors | Critical |
As can be seen from the table, the combined method requires the greatest care. In such cases, it is recommended to have manual for repairing a specific modification on hand. The Octavia A7 is most commonly used as a combination of locks and bolts, requiring consistent execution of all steps.
Do not forget that improper dismantling can lead to a violation of the geometry of the body during subsequent assembly. This is especially important for vehicles with a high degree of passive safety.
Installation and reassembly
The assembly of seats is carried out in reverse order. First, set the back, hooking it to the upper locks and screwing the lower bolts. Make sure the back is flat and has no backs.
Then install the bottom pillow. Combine the holes in the locks with the eyelets on the floor and tap until the characteristic click. Check the reliability of the mounting by pulling the seat in different directions.
After installation, check the operation of all mechanisms: folding the back, adjusting the height of the head restraints and the operation of seat belts. Make sure that nothing interferes with the movement of the elements.
- β Check the density of the seats to the floor
- β Make sure there are no creaks and backlashes
- β Test the operation of all seat functions
If you have installed the seat after repair, check all safety systems. This is critical to ensuring that passengers are protected in the event of an accident.
Proper installation of seats guarantees not only comfort, but also the safety of passengers in case of accident.
Common mistakes and how to avoid them
One of the most common mistakes is trying to remove the seat without first checking all the fasteners. This may cause plastic parts to break or damage to the upholstery.
Another mistake is using the wrong tools. Sharp metal objects can scratch the plastic or leave marks on the leather. Always use plastic spatulas or cloth-wrapped screwdrivers.
You should also avoid sudden movements when removing and installing. Smooth and controlled actions will help maintain the integrity of all parts and mechanisms.
β οΈ Caution: Never use metal tools directly on plastic interior parts. This is guaranteed to leave deep scratches.
If you doubt your abilities, it is better to turn to professionals. Incorrect installation can lead to serious consequences, including failure of safety systems.
FAQ: Frequently asked questions
Do I need to disconnect the battery before removing the seats?
In most cases, it is not necessary to disconnect the battery, since the seats are not permanently connected to the on-board power supply. However, if you plan to work on under-seat wiring (such as heating), disconnecting the battery is a safe solution.
Is it possible to remove only one part of the rear sofa?
Yes, on Skoda Octavia A7 the rear seat is usually split in two (40:60 or 50:50). You can remove any part separately by releasing the corresponding clips and bolts.
What should I do if the latches do not snap off?
Try rocking the seat slightly from side to side while lifting it up. If that doesn't work, check for hidden bolts or latches that you may have missed.
How to preserve the latches when removing them?
Use plastic paddles to pry up the seats and avoid using excessive force. If the clips are stuck, try wiggling them slightly to loosen them.
Can the seat be used without a backrest?
Technically it is possible, but it violates the operating rules and can be dangerous. The backrest is necessary to support passengers and operate safety systems.