Rear view camera on Skoda Superb 3: how to select, install and configure

Rear view camera Skoda Superb 3 (2015–2023) is not just a comfort option, but a critical safety element. In dense city traffic or tight parking lots, even experienced drivers run the risk of hitting an obstacle without seeing it in their mirrors. Standard camera included Style and Laurin & Klement offers permission 720p, but what to do if it is not in the basic version or it is out of order?

In this article we will look at everything: from choosing an original camera 5E0 907 575 before installing analogues with improved night photography, connecting to the radio Bolero or Columbus, as well as diagnosing typical faults - from a blurred image to an error No Signal. We will place special emphasis on unique feature of Superb 3: integration of the camera with the system Park Assist, which requires correct calibration after replacement.

Which rear view cameras are suitable for Skoda Superb 3

Original camera for Superb 3 has an article number 5E0 907 575 (or 5E0 907 575 A for restyled models 2019+). It is installed under the logo Škoda on the rear door and connects to the control unit J743 (Park Assist). However, there are alternatives on the market with better characteristics:

• 🔹 Original VW Group: Articles 5Q0 907 575 (from Passat B8) or 3G0 907 575 (from Golf 7) - connector compatible, but require adaptation via VCDS.
• 🔹 Analogues with improved optics: For example, HELLA 8ZL 351 101-121 (resolution 1080p, viewing angle 170°).
• 🔹 Universal cameras: Heated and night illuminated (e.g. Rear View Safety RVS-062713), but the mounting will need to be modified.

When choosing, pay attention to connector type: y Superb 3 6-pin connector is used FAKRA (encoding Z>). Cameras with a different connector will require resoldering or an adapter.

Important: if your Superb 3 equipped with a system Trailer Assist (trailer assist), the original camera must support this function. Otherwise, when connecting a trailer, the image will not be mirrored correctly.

How to connect a rear view camera to the radio

The connection process depends on the type of head unit. B Superb 3 There are three main options:

head unit	Camera connector	Required adaptation
Bolero (5E0 035 680)	Quadlock (T10a), contact A8	Encoding via VCDS: Byte 0 → Bit 4 = 1
Columbus (3T0 035 680)	FAKRA (Z), direct integration	Activation in 5F-Information Electr. → Camera
Amundsen (5E0 035 663)	Mini-FAKRA (Y)	Additional module RVC (art. 5E0 907 441)

To connect, follow these steps:

1. Remove the trunk trim and locate the camera connector (usually near the rear door lock).
2. Connect the camera to the connector, observing the polarity (pin 1 — +12V, 6 — GND).
3. Route the cable along the left post to the head unit (use standard corrugations).
4. In the radio, activate the camera function through the diagnostic software (VCDS, ODIS or OBDeleven).

Disconnect the battery (minus terminal)

Check cable integrity with a multimeter

Make sure the connectors are compatible

Prepare tools: plastic spatulas, T20/T25 screwdrivers

-->

⚠️ Attention: If after connecting the camera works, but the image is upside down, you need to change the parameter Camera View in the block 5F to the value Mirrored. This often happens when using universal cameras.

Setting up a camera via VCDS: step-by-step instructions

For correct operation of the rear view camera on Skoda Superb 3 software adaptation required. Without it, the radio may not recognize the signal or display an error. Parking System Malfunction. We use a diagnostic scanner VCDS (or its analogues):

1. Connect the scanner to OBD-II connector (located under the steering wheel on the left).
2. Launch the program and select a model Skoda Superb 3 (5E).
3. Go to block 5F-Information Electr. (Infotainment).
4. Select Adaptation → Channel 6 → Camera.
5. Set value 1 for parameter RVC_Installed.
6. In the block 10-Park/Steer Assist perform basic setup (Basic Settings) for calibrating sensors.

If the camera is connected but the image does not appear, check:

• 🔌 Correct connector connection FAKRA (contacts must not be oxidized).
• 📶 Presence of voltage 12V on contact 1 (checked with a multimeter).
• 🔧 Compliance with the radio firmware (update via MIB2_Update, if the version is older 0560).

⚠️ Attention: When replacing the camera with a non-original one, you may need to disable the function Dynamic Guidance Lines (dynamic parking lines). Otherwise, they will not display correctly due to differences in lens focal length.

Typical faults and solutions

Even original cameras Skoda Superb 3 they fail over time. Let's look at the most common problems and their solutions:

Symptom	Possible reason	Solution
The image is blurry or noisy	Lens contamination or contact oxidation	Clean the lens with alcohol, check the connector FAKRA
The camera does not turn on in reverse gear	Broken wire +12V or reverse sensor malfunction	Test the circuit with a multimeter and check the fuse. F42 (10A)
Parking lines don't match reality	Calibration lost after replacing camera	Configure via VCDS → 10-Park Assist → Basic Settings
Error No Signal on the screen	Incompatibility of the camera with the radio or cable damage	Check the compatibility of the articles, replace the cable

Pay special attention wiring: in Superb 3 The camera cable runs through the corrugation along the left pillar of the body. Often it rubs against metal edges, which leads to a short circuit. For prevention, use additional insulation (for example, heat-shrink tubing).

What to do if the camera only works during the day?

If the camera does not show well in the dark, the problem may be the lack of IR illumination. Original cameras Skoda are not equipped with it, but the system can be modified:

1. Install additional IR LEDs (for example, Osram LEDriving FOG 101) next to the camera.

2. Connect them to the rear light circuit via a relay so that they turn on when reverse gear is activated.

3. Adjust the camera sensitivity via VCDS → 5F → Adaptation → Night_Vision = 1.

Improved visibility: optional accessories

Standard camera Superb 3 has a viewing angle 130°, which is sometimes not enough for maneuvering in cramped conditions. Let's look at ways to improve your review:

• 🔍 Wide angle attachments: For example, Aukey Ora Lens increases the angle to 170° without loss of quality.
• 📱 Wireless cameras: Models with signal transmission Wi-Fi (for example, Yada Digital Wireless) allow you to display an image on a smartphone in parallel with the radio.
• 🔦 Additional lighting: LED strips Philips LED DayLight around the license plate will improve visibility in the dark.

For owners Superb 3 with the system Area View (all-round view) it is recommended to install additional cameras in the front bumper and under the mirrors. This will enable the function 360° through the radio Columbus (firmware required MIB2.5 and above).

Replacing a rear view camera with your own hands

If you decide to replace the camera yourself, prepare the following tools:

• 🔧 Plastic spatulas for removing trim.
• 🔨 Screwdrivers T20 and T25 (for trunk mounts).
• 📸 Multimeter for checking the circuit.
• 🧴 Silicone grease for the chamber rubber seal.

Step by step instructions:

1. Open the back door and remove the plastic trim from the inside (carefully pry it up with a spatula, starting from the corner).
2. Unscrew the two camera mounting bolts (T20) and disconnect the connector FAKRA.
3. Install the new camera, first applying silicone to the seal (this will prevent moisture from entering).
4. Connect the connector and check operation by engaging reverse gear.
5. Reassemble the trim in reverse order, making sure all clips snap into place.

⚠️ Attention: When installing a heated chamber (for example, HELLA 8ZL 351 101-121) it is necessary to connect additional wires to the rear window heating circuit (fuse F38 (20A)). Incorrect connection may result in circuit overload!

Frequently asked questions about the rear view camera of the Skoda Superb 3

Is it possible to install a rear view camera on the basic equipment? Superb 3 without Park Assist?

Yes, but you will need:

1. Buy a camera with an article number 5E0 907 575 and module RVC (art. 5E0 907 441).
2. Connect the camera to the radio and route the wiring to the unit J743 (if you don't have one, you'll need an emulator).
3. Activate the function via VCDS in blocks 5F and 10.

The cost of such an upgrade will be ~25–30 thousand rubles, including work.

Why does the following message appear on the screen after replacing the camera? Camera Error?

This error occurs due to:

• Incompatibility between the firmware of the radio and camera (update the software via MIB2_Update).
• Lack of adaptation in the block 5F (check the parameter RVC_Installed).
• Damage to the cable (check the circuit from the camera to the radio).

Solution: reset the radio settings (Reset to Default in VCDS) and repeat the adaptation.

How to calibrate parking lines after replacing the camera?

For calibration:

1. Place the car on a level surface.
2. Connect VCDS and go to the block 10-Park/Steer Assist.
3. Select Basic Settings → Group 060.
4. Follow the instructions on the screen (you will need to press the brake pedal and engage reverse gear).

If the lines still do not match, check the camera installation height - it should be 70–75 cm from the ground.

Which cameras support the function Trailer Assist?

For work Trailer Assist Only original cameras are suitable:

• 5E0 907 575 B (for models from 2019).
• 5Q0 907 575 C (from Passat B8, requires adaptation).

Universal cameras do not support this function, since they do not transmit data about the angle of rotation of the trailer to the unit J743.

Is it possible to connect the camera to the radio? Bolero without a diagnostic scanner?

Technically yes, but:

• Without VCDS you will not be able to activate the camera display on the screen.
• You can use a workaround: connect the camera via AV-in (if any), but the parking lines will not work.
• For full integration you will need at least OBDeleven (budget analogue VCDS).