Lamps in the ŠKODA Octavia A5 FL (restyled 2009–2013): choice, replacement and nuance

Owners ŠKODA Octavia A5 After facelift (2009-2013) sooner or later faced with the need to replace lamps - whether it is burned out halogen in headlight, dim brake light or out of order size. Despite the reputation of the Czech car as a reliable workhorse, the lighting system requires attention: from the correct selection of lamps to the right level. type of base until the nuances are observed during installation.

In this article we will analyze all types of lamps used in Octavia A5 FL, with the indication of original articles, proven analogues and step-by-step instructions for replacement. Particular attention should be paid to typical errors (for example, confusion). H7 and H1 caps in block lights) and ways to extend the life of the lighting. The material is relevant for all bodies of the restyled version: liftback, wagon Combi and Scout.

What lamps are in the ŠKODA Octavia A5 FL: a full list of zones

Lighting equipment Octavia A5 After facelift in 2009, there have been minimal changes compared to the preresty style, but there are key differences. For example, in the top trim levels appeared bi-xenon headlights with autocorrectorand in the basic - modified block headlights under halogen H7. Below is a table with the distribution of lamps by nodes.

Important: in versions with xenon (optional 8X1 or 8X2) passing beam is provided by a gas discharge lamp D1SAnd the far halogen H7. When replacing xenon required zeroing out via a diagnostic scanner (for example, VCDS), otherwise the control unit will signal a malfunction.

For an accurate definition of the type of lamps in your configuration, check the sticker on the back of the block headlight or use VIN decoder (for example, on the website ŠKODA). The original lamps are listed in the following section.

Original articles and the best analogues: what to choose?

Original lamps from ŠKODA (manufacturer - Hella or Osram) are of stable quality but are often overpriced. Like a couple of halogens. H7 with article number N10320101 will cost 1,200-1,500 rubles, while analogues from Philips or Bosch They are 2-3 times cheaper with a comparable resource.

The table below shows proven analogues for key lighting zones, including variants with increased brightness (see below).+30%/+50%) and extended service life (Long Life).

⚠️ Attention: Lamps with markings «+150%» or «Super White» (for example, Osram Cool Blue) may blind oncoming drivers and break down faster. For Octavia A5 FL Best choice - options with an increase in brightness to +50% color-temperature 3200–4300K.

For fog lights (base H8/H11) we recommend Philips X-tremeVision (H8 12362XV) - they give a clear cut-off line and do not dazzle when properly adjusted. When replacing PTP, be sure to check the condition scattererIf it is cloudy, the lighting efficiency drops by 30-40%.

Step-by-step replacement of low and high beam lamps

Replacing lamps in headlights Octavia A5 FL does not require special tools, but there are some nuances. For example, to access passing beam lamp (H7) remove battery (left headlamp) or air filter (right) Let’s look at the example of the halogen version.

Remove the negative terminal from the battery |Clear hands (do not touch the halogen bulb) |Prepare a new lamp and gloves |Check the safety circuit (F3/F13 for passing beam)->

Instructions for passing beam lamp (H7):

1. Open the hood and remove plastic cover on the back of the lights (turn counterclockwise).

2. Disconnect power connectorby pressing the latch.

3. Remove spring retainerKeep the lamp in place: Pull it up and pull it away.

4. Remove the old lamp, install a new one. H7without touching the flask (use gloves or a cloth).

5. Lock the lamp with a spring, connect the connector and install the cover.

⚠️ Attention: If the lamp does not light after replacement, check fuse (10A) in the mounting block under the steering wheel. It often burns out due to a short circuit in the circuit. Also make sure that lamp base I went right into the grooves. Octavia A5 FL There are cases where the lamp is H7 It is in the mirror due to incorrect installation.

For replacement high beam lamps (H1) The algorithm is similar, but the lock has a different design (metal bracket instead of spring). In the versions with xenon discharge-lamp replacement D1S Remove the entire headlight and zero the error through the diagnosis.

Replacement of lamps in rear lamps: stop lamps and dimensions

Tail lights Octavia A5 FL have a modular design: to replace lamps do not need to remove the entire unit, just click plastic cover inside the trunk. But in the station wagon Combi Access is complicated by the skin - you have to dismantle some of the plastic.

Procedure for stop lamp/size lamp (P21/5W):

1. Open the trunk and remove decorative overlay on the side panel (from the side of the replaced lamp).

2. Click on lamp-lid (2 pcs) and take it off.

3. Turn the lamp socket P21/5W counterclockwise and remove it.

4. Replace the lamp, install the cartridge back and check the operation of both threads (size and stop light).

⚠️ Attention: B Octavia A5 FL often burns out strand lamp-light P21/5W, mientras que the stop signal thread remains operational. If the size does not burn after replacement, check fuse (7.5A) and contacts in the socket They can become oxidized due to moisture.

For replacement reversing lamps (W16W) or turn-piece (PY21W) The algorithm is similar, but the cartridges are located closer to the center of the flashlight. In the versions with LED stops (optional 8Z4) no lamps - the entire module must be replaced when the failure occurs.

Typical Lighting Problems and How to Solve Them

Owners Octavia A5 FL Often face lighting faults that are not always associated with burnt out lamps. Let’s look at the most common cases and methods of their elimination.

• 🔋 Both low beam headlights do not light up - check J357 relay (in the driveway block) and fuse. Often the problem is caused by oxidation of contacts in the block headlight connector.
• 💡 High-beam light blinks - the fault of poor contact in the cartridge or Failure of the light control module (J519). Try to clear your contacts. T10e and T10f in the mounting block.
• 🌫️ Headlight dispersal is clouded Use polymer for plastic (e.g., 3M Headlight Restoration Kit). In advanced cases, a replacement of the lens (article) will be required. 6U2941007/008).
• 🚨 The "Check Light System" Error - clear it with VCDS in the block 09-Cent. Elect.. If an error is returned, check low beam lamp or Light level sensor (G39).

The problem with oxidation of contacts in the block lights. Due to the ingress of moisture through the seals connectors T10 They corrode, which leads to light flickering or complete failure. For prevention, process contacts contact lubricant (for example, Liqui Moly Kontakt-Spray) and check the integrity sealing rubber bands on the headlights.

Adjusting headlights after replacing bulbs

After installing new lamps (especially if they have increased brightness) be sure to adjust the light beam. B Octavia A5 FL for this purpose are provided vertical and horizontal alignment on top of the block lights. Correct adjustment prevents oncoming drivers from dazzling and ensures maximum road visibility.

Step by step instructions:

1. Place the car on a level area 5 meters from the wall (or a special screen).

2. Check tire pressure and load: only the driver should be in the cabin, and in the trunk - a spare and a standard set of tools.

3. Turn on low beam and open the hood. On the wall, mark the center of the light spots from each headlight.

4. With 6mm hexagon Adjust the screws:

   • Top screw - vertical position (The cut-off shall be 5 cm below the centre height of the headlamp).
   • Side screw - horizontal position (The light beam should be parallel to the longitudinal axis of the car).

⚠️ Attention: In versions with automatic headlight leveler (optional 8Q1) the setting shall be automatically adjusted when the ignition is activated. If the corrector knocked down the settings (for example, after replacing the lamps), reset it through VCDS in the block 55-Headlight Rangeby selecting Basic Settings → Channel 01.

To check the result, drive along a dark section of the road: the light beam should illuminate 40-50 meters ahead without the blinding effect on oncoming cars. If the boundary of light shade is blurred, problems with headlight reflector (for example, after an accident).

Lighting upgrades: legal and illegal options

Many owners Octavia A5 FL They want to improve lighting, but not all methods are allowed by traffic rules. Consider the legal and prohibited options for modernization.

• ✅ Legal improvements:
  • 💡 Installation of lamps with increased brightness (up to +50%) while maintaining the cap and color temperature (for example, Osram Night Breaker).
  • 🔦 Polishing of headlight lens to restore transparency.
  • 🔄 Replacement of halogens with LED lamps with ECE certificate (for example, Philips X-tremeUltinon) if they are listed as permitted for your model.
• ❌ Illegal (fine 500-3,000 rubles):
  • 🚨 Installation xenon to halogen headlights (even with lenses).
  • 🔴 Use of LED lamps without certification or with incorrect light distribution.
  • 🟡 Lamps with a higher color temperature 5000K (blue spectrum).

The most reliable way to improve lighting is to replace it. headlight on version with lensed optics (article 6U2941009/010 for xenon. They provide a clear cut-off boundary and 30% better illumination. However, the cost of such an upgrade starts from 20,000 rubles per pair.

Alternative - installation bi-xenon lenses (c) the standard headlamps (e.g. kit from Morimoto) but this requires:

1. Right setup cutter (Light limit).
2. Connections through ignition unit with CAN bus.
3. Zeroing errors through VCDS.

Without these measures, blinding oncoming drivers is inevitable.

FAQ: Frequent questions about lamps in the ŠKODA Octavia A5 FL

1. Connect VCDS.
2. Go to block 09-Cent. Elect.
3. Select "Clear DTCs."