Windshield Škoda Fabia 2: how to choose, replace and save

Windshield Škoda Fabia second generation (2007–2014) is not just a body element, but a critical part that affects safety, visibility and even the operation of the vehicle’s electronic systems. Owners of this model often encounter problems: from cracks after getting hit by a stone to clouding of the glass due to wear. But how to choose a quality replacement without overpaying for the brand? And why is the original glass from VW Group Can it cost 2-3 times more than analogues?

In this article we will look at all the nuances: from article numbers and manufacturers to step-by-step replacement instructions (including sensor calibrationif your Fabia 2 equipped with a system Lane Assist). You will also learn how to avoid common installation mistakes that lead to leaks or squeaks, and why cheap glass from China can lead to problems with heated wiper area. Let's start with the main thing - how to determine which glass is suitable for your modification Fabia 2.

How to determine the original windshield for Škoda Fabia 2

The first thing to do is specify body modification. Fabia 2 was produced in three versions:

• 🚗 Hatchback (5D) — the most common, glass articles differ from the sedan;
• 🚖 Sedan (NB) - the windshield is narrower and higher, often confused with Roomster;
• 🚙 Combi (5J) - station wagon, glass identical to the hatchback, but with different seals.

Original glasses are produced under the brand Saint-Gobain Sekurit (labeling SG in the corner) and have articles:

⚠️ Attention: If your Fabia 2 released after 2012, check availability forward facing cameras (installed near the rear view mirror). In this case, you will need glass with marked "A5" and an additional area for camera mounting. Installing the wrong glass will result in an error 01317 — Camera for Lane Assist in the block BCM.

Top 5 analogs of original glass: what to choose instead of OEM

Original glass from Sekurit will cost 18,000–25,000 rubles (for 2026), but the market offers worthy analogues at a lower price. The main thing is to avoid “no-name” options from China, which may have:

• 🔍 Optical distortion ("lens" effect around the edges);
• ☀️ Bad tinting (does not meet standard 70% light transmission);
• ⚡ Heating not working (burns out after 1–2 years).

Rating of trusted manufacturers (price/quality):

1. Pilkington (UK) - article PFG 12345 (for hatchback). Price: ~12,000 rub. Better balance in terms of price/quality ratio, corresponds to OEM in thickness (4.76 mm).
2. AGC (Japan) - article AGC 845011. Price: ~14,000 rub. It is characterized by increased impact resistance, but may be more sensitive to temperature changes (risk of cracks in winter).
3. XYG (China, premium line) - article XYG-SK002. Price: ~9,000 rub. Good budget option, but check ECE R43 certificate (must be included).
4. Guardian (USA) - article GU 6Y1845. Price: ~15,000 rub. High quality, but rarely found in Russia.
5. Benson (Taiwan) - article BEN-FAB2. Price: ~8,000 rub. The cheapest option, but only for models without electronics (no zone for sensors).

💡 Tip: If your Fabia 2 equipped climate control, avoid glass without green stripe in the upper part - it reduces the heating of the cabin in summer. In analogues Pilkington and AGC This strip is there by default.

Step-by-step instructions for replacing a windshield

Replacing glass with Fabia 2 takes 2–3 hours and requires two people (glass is heavy and fragile). If you decide to do this yourself, prepare:

A special knife for cutting glue (for example, U-Pol 1000>)

New glass with seal

Sealant SikaTack Drive or 3M 08609>

Suckers for glass (minimum 2 pcs.)

T25 screwdriver for removing wipers and plastic panels

Construction hair dryer (for heating the glue)

Gloves and masking tape -->

🔧 Step 1: Removing the old glass

1. Remove the wipers (unscrew the nuts with a wrench 13 mm).
2. Remove the plastic trim under the windshield (snap off the clips with a screwdriver).
3. Using a glue knife, carefully cut the sealant around the perimeter. Start from the top corner - the glue is thinner there.
4. Use suction cups to remove the glass. Don't pull too hard - it may crack!

🔧 Step 2: Preparing the opening

Remove any remaining old glue with a spatula or drill with a brush attachment. Please note drainage holes at the bottom of the opening - they must be clean, otherwise water will accumulate. Before installing new glass, apply primer for glass (for example, 3M 05907) to the metal of the body.

Adaptation → Block 5F (Information Electr.) → Camera → "Basic Setting" → "Calibration"

1. Connect the scanner to the OBD-II connector.
2. Select block 5F (Info Electr.) → "Basic Settings".
3. Select Camera Calibration and follow the onscreen instructions.
4. Place the target 3 m from the bumper.
5. Wait for the process to complete (takes 5-10 minutes).