Error 01316 on cars Škoda - one of those problems that can unsettle even experienced car owners. This DTC is related to ABS/ESP system It can be used as a budget model (Fabia, Rapid) and on the premiums (Superb, Kodiaq). Depending on the generation of the car and the installed electronic control unit (ECU), the consequences of ignoring this error can range from minor inconveniences to complete loss of control over the braking system.

Unlike many other codes, 01316 does not always indicate a critical failure - sometimes it is caused by a simple sensor failure or contact oxidation. However, in 30% of cases (according to statistics from service centers Škoda in Russia) this error hides more serious problems: from wear of the wheel bearings to a malfunction of the ABS hydraulic unit. In this article we will look at all possible scenarios for error 01316, including rare cases when it is caused by non-original spare parts or incorrect software after flashing the computer.

What does error 01316 mean on Škoda: decoding the code

Code 01316 in the self-diagnosis system Škoda stands for "Implausible Signal from Wheel Speed Sensor" (implausible signal from wheel speed sensor). This means that the ABS/ESP ECU receives data from one or more sensors that do not correspond to physically possible values. For example:

  • 🚗 Zero speed when the car is moving (the sensor is “stuck” or disabled).
  • 🌀 Jumping readings (from 0 to 200 km/h in a fraction of a second).
  • ⚡ There is no signal at all (open circuit or sensor malfunction).

It is important to understand that the error 01316 - this is not a sentence, but symptom. It can be caused either by a problem with the sensor itself or by faults in related systems: wiring, wheel bearing or even the ABS control unit. On models Škoda Octavia A5/A7 and Superb B6/B8 this code is often accompanied by lights coming on ABS and ESP on the dashboard.

⚠️ Attention: If error 01316 appears simultaneously with the code 00283 ("ABS Wheel Speed Sensor - No Signal"), the probability of mechanical damage to the sensor or wiring is 85%. In this case, a visual inspection is required, and not just computer diagnostics.

The main reasons for error 01316

Reasons for the error 01316 can be divided into three categories: mechanical, electric and software. Below is a complete list of possible culprits with an indication of their frequency of occurrence (according to Škoda Auto Russia and independent services):

Reason Frequency (%) Models where it occurs most often
Damage to the wheel speed sensor 40% Fabia MK2, Rapid, Roomster
Oxidation/broken wiring 25% Octavia A5, Yeti
Wheel bearing wear 20% Superb B6, Kodiaq
ABS/ESP unit malfunction 10% Octavia A7, Karoq
ECU firmware failure 5% Scala, Kamiq (after software updates)

By car Škoda with the system MQB (platform Octavia A7, Superb B8, Karoq) error 01316 often occurs after replacing a hub or brake disc if the technician did not observe the bolt tightening torque (should be 45–50 Nm). This leads to play and distortion of the sensor signal.

📊 On which Škoda model did you encounter error 01316?
  • Octavia
  • Superb
  • Fabia
  • Rapid
  • Kodiaq
  • Other model

How to diagnose error 01316 yourself

To accurately diagnose the error 01316 you will need a scanner that supports the protocols OBD-II and UDS (for example, VCDS or ODBEleven). However, even without specialized equipment, you can perform a preliminary check:

  1. Visual inspection of sensors:
    • 🔍 Check the integrity of the sensor housing (cracks, chips).
    • 🧲 Make sure there are no metal shavings (a sign of bearing wear).
    • 🔌 Inspect the connector for oxidation or moisture.
  • Clearance check: The optimal gap between the sensor and the hub gear is - 0.8–1.2 mm. Use a probe or plastic card.
  • Wiring test: Using a multimeter, test the circuit from the sensor to the ABS unit (the resistance should be 800–1400 Ohm).

    • If you have access to a diagnostic scanner, follow these steps:

    1. Connect to the block 03-ABS Brakes.
    2. Count errors and write them down freeze frame (data about the state of the system at the time the error occurred).
    3. Check sensor readings in real time (Measuring Blocks → group 004 or 008).

    ☑️ Preparing to diagnose error 01316

    Done: 0 / 5
    ⚠️ Attention: On models Škoda with the system EDL (electronic differential lock) error 01316 can lead to spontaneous brake application at speeds up to 30 km/h. In this case, operating the vehicle is prohibited!

    Step-by-step instructions for resolving error 01316

    The repair algorithm depends on the identified cause. Below is a universal instruction covering 90% of cases:

    1. Replacing the wheel speed sensor

    If the sensor is damaged or its resistance is outside the limits 800–1400 Ohm:

    1. Disconnect the sensor connector and remove it from the mount (usually one bolt per 8 mm).
    2. Clean the seat from dirt and rust.
    3. Install a new sensor (original part numbers for Škoda: 1K0 927 801 - front, 1K0 927 802 - rear).
    4. Connect the connector and reset the errors via the scanner.

    2. Wiring repair

    If wires are broken or oxidized:

    • 🔧 Clean the contacts in the connector of the sensor and the ABS unit.
    • 🔌 Replace damaged sections of wire (use heat shrink tubing for insulation).
    • 🛠️ Check the ground of the ABS unit (usually located under the battery or on the body next to the ECU).

    3. Replacing the wheel bearing

    If the bearing play exceeds 0.05 mm or a hum is heard when driving:

    1. Remove the wheel and brake disc.
    2. Unscrew the hub nut (tightening torque during installation - 180–220 Nm).
    3. Replace the bearing assembly with the hub (for example, SKF VKBA 3600 for Octavia A5).
    4. Install a new speed sensor (the old one may be damaged during removal).
    💡

    After replacing the wheel bearing, be sure to ABS sensor calibration via diagnostic scanner (in VCDS - function Basic Settings → group 004). Without this, error 01316 may return after 100–200 km.

    4. Firmware for ABS unit

    If the error appears after updating the software or replacing the ECU:

    • 📱 Connect to the block 03-ABS Brakes through ODIS or VCDS.
    • 🔄 Reset adaptations (Security Access → code 40168).
    • 💾 Reflash the unit with the original software (the version must match the vehicle VIN).

    Common repair mistakes and how to avoid them

    Many car owners and even mechanics make critical mistakes when troubleshooting codes. 01316, which leads to a relapse of the problem. Here are the most common mistakes:

    • 🛑 Use of non-original sensors. Cheap analogues (for example, from Febi or SWAG) often have inadequate resistance or magnetic induction, causing false alarms. Original sensors Škoda/VW last 3–4 times longer.
    • 🔧 Failure to comply with the tightening torque. An overtightened sensor bolt deforms its body, and loose tightening leads to vibrations and signal loss.
    • 🔌 Ignoring the "mass". Oxidation of the ground contact of the ABS unit (usually under the battery) is the cause of 15% of recurrences of error 01316.
    • 📉 Lack of calibration. After replacing a hub or sensor, be sure to Basic Settings in the ABS unit, otherwise the ECU will receive incorrect data.
    ⚠️ Attention: By car Škoda with the system 4Motion (all-wheel drive) error 01316 may block switching between modes 2WD/4WD. In this case, a complete reboot of the ECU is required (Battery Reset through VCDS).
    What happens if you ignore error 01316?

    Driving for a long time with a faulty speed sensor leads to:

    • 🚨 Disabling ABS and ESP (braking distance increases by 20–30%).
    • 🔥 Overheating of brake pads due to uneven distribution of effort.
    • 🛞 Accelerated tire wear (incorrect operation of the stability control system).
    • 💥 Damage to the ABS unit (the hydraulic unit may fail due to constant false signals).

    On models with adaptive cruise control (ACC) error 01316 completely disables the system, which is dangerous on the highway.

    Cost of repairs in service vs. self-removal

    Error repair prices 01316 vary depending on the cause and region. Below are the average prices for Moscow and the regions (for 2026):

    Type of work Cost (Moscow, rubles) Cost (regions, rubles) Working hours
    Diagnostics (scanner + visual inspection) 1 500–2 500 800–1 500 30–60 min
    Replacing the speed sensor (1 pc.) 2 000–3 500 1 200–2 500 1–1.5 h
    Replacing the wheel bearing 5 000–8 000 3 500–6 000 2–3 hours
    Wiring repair (soldering, insulation) 1 500–3 000 1 000–2 000 1 hour
    ABS unit firmware 3 000–5 000 2 000–3 500 1.5–2 hours

    Do-it-yourself repairs will be cheaper, but will require tools:

    • 🔧 Speed sensor (original) - 1 800–3 000 ₽.
    • 🔩 Wheel bearing — 4 000–7 000 ₽ (complete with hub).
    • 📶 Diagnostic cable (VCDS HEX-V2) — 15 000–20 000 ₽ (one-time activation costs 1 000 ₽).
    💡

    Saving on diagnostics often leads to higher repair costs. For example, replacing a sensor without checking the bearing may, after 500 km, result in the need to replace the entire hub assembly.

    Prevention of error 01316 on Škoda

    Prevent the error from occurring 01316 easier than eliminating its consequences. Follow these guidelines:

    • 🚿 Washing wheel arches. Dirt and salt in winter accelerate corrosion of sensors and wiring. Use anti-corrosion sprays (for example, Liqui Moly Unterbodenschutz).
    • 🔄 Regular diagnostics. Check for errors with a scanner every 10,000 km (or before long trips).
    • 🛠️ Timely replacement of bearings. At the first sign of hum or play (even if there is no error), replace the bearing - this will protect the sensor from damage.
    • ⚡ Voltage control. The voltage drop in the on-board network is lower 11.8 V may cause sensor malfunctions. Check the generator and battery.

    By car Škoda with the system Predictive Cruise Control (adaptive cruise) error 01316 may appear after installing non-standard rims with a changed offset (ET). In this case, the ABS ECU needs to be reflashed to new parameters.

    FAQ: Frequently asked questions about error 01316

    Is it possible to drive with error code 01316?

    Short term - yes, but with caution. Systems will shut down ABS and ESP, which will increase the braking distance and the risk of skidding. At a higher speed 100 km/h Driving becomes dangerous. Long driving (more than 200 km) may damage the ABS unit.

    Why does error 01316 appear only in cold weather?

    This is a typical sign microcracks in the wiring or contact oxidation. At low temperatures, the metal contracts and damaged areas lose conductivity. Solution: Warm up the car in a warm garage and check the sensor circuit with a multimeter.

    How to reset error 01316 without a scanner?

    On most models Škoda You can reset the error by disconnecting the battery at 10–15 minutes. However, this is a temporary solution - if the cause is not eliminated, the code will return. On machines with the system MQB (for example, Octavia A7) requires a scanner for a full reset.

    Could error code 01316 be caused by faulty brake pads?

    No, directly - no. However worn pads (thickness less 3 mm) or warped brake discs may cause vibrations that distort the sensor signal. In this case, error 01316 will be accompanied by the code 01130 ("ABS Operation Implausible Signal").

    Which speed sensors are suitable for Škoda?

    Use only original spare parts or certified analogues with markings VW Group:

    • Front sensor: 1K0 927 801 A (until 2012) or 5Q0 927 801 (MQB platform).
    • Rear sensor: 1K0 927 802 A or 5Q0 927 802.

    Cheap analogues (for example, Febi 23616) may not match the resistance and cause the error to recur.