ŠKODA Kodiaq is one of the most popular crossovers in Russia, but its dimensions and ground clearance make the sills vulnerable to mechanical damage, corrosion and chips. Owners often face a problem: the factory protection quickly wears out, especially in winter, when the reagent is used extensively on the roads. In this article we will look at which thresholds are suitable for Kodiaq, how to choose and install them correctly in order to extend the life of the body and maintain the presentable appearance of the car.

We analyzed reviews from owners, technical characteristics of original and alternative solutions, as well as installation nuances. We will pay special attention to materials (aluminum, plastic, stainless steel), brands (for example, Heko, EGR, Skoda Original) and typical installation errors. If you plan to protect your thresholds Kodiaq, this article will help you avoid costly mistakes and choose the optimal solution for your budget and operating conditions.

Why are thresholds needed on the ŠKODA Kodiaq: problems and solutions

Thresholds ŠKODA Kodiaq - this is not only a design element, but also a critical part of the body that takes on the main mechanical loads. In Russian realities they suffer from:

  • 🧊 Reagents and salts — in winter, road services actively use chemical compounds that corrode the paintwork and provoke corrosion.
  • 🪨 Gravel and sand — when driving on dirt roads or gravel roads, small stones hit the bottom of doors and sills, leaving chips.
  • 🚗 Parking lots and curbs - due to large dimensions Kodiaq owners often touch the thresholds when parking, especially in tight yards.
  • 💧 Moisture and dirt — in rainy weather, the thresholds are constantly in contact with water, which accelerates the formation of rust.

Factory thresholds Kodiaq covered with a thin layer of paint and primer, which is quickly erased. Even original protection (if there is one) does not always save: plastic linings crack in the cold, and metal linings corrode from the inside. The solution to the problem is to install additional thresholds or completely replace them with reinforced analogues.

⚠️ Attention: If pockets of rust have already appeared on the thresholds, before installing new protection, be sure to remove the corrosion and treat the metal with an anti-corrosion agent. Otherwise, rust will continue to spread under the new coating.
📊 What door sill material do you prefer for the Kodiaq?
  • Aluminum
  • Stainless steel
  • Plastic
  • Original factory

Types of thresholds for ŠKODA Kodiaq: comparison of materials and brands

There are thresholds on the market for Kodiaq from different materials, each of which has its own pros and cons. Let's look at the main options:

Material Benefits Disadvantages Average price (set)
Aluminum Light, resistant to corrosion, well-kept shape Expensive, may become deformed if subjected to strong impacts 12 000 — 20 000 ₽
Stainless steel Strong, durable, protects against mechanical damage Heavy, may rust in weld areas 8 000 — 15 000 ₽
Plastic (ABS, polyurethane) Cheap, lightweight, does not rust, easy to install Brittle in the cold, scratches quickly 3 000 — 7 000 ₽
Original (Skoda) Perfect fit, guaranteed Expensive, often require painting 15 000 — 25 000 ₽

Among the brands stand out:

  • 🔧 HEKO - a German manufacturer, offers aluminum and steel thresholds with precise adjustment to Kodiaq. Popular model HEKO 910 with anti-gravel coating.
  • 🔧 EGR - Italian brand, specializes in plastic linings with reinforced fastenings. A good option for budget protection.
  • 🔧 Skoda Original - original parts, but often require modification (for example, painting) and are much more expensive than analogues.
  • 🔧 AutoStyle is a Russian manufacturer that offers inexpensive powder-coated steel thresholds.

Aluminum thresholds from HEKO with anti-gravel film showed the best results in tests for resistance to corrosion and mechanical damage among analogues (according to Za Rulem magazine, 2023). However, if the budget is limited, plastic linings EGR will be a temporary but effective solution.

How to choose thresholds for ŠKODA Kodiaq: step-by-step instructions

The choice of thresholds depends on the goals: whether you want to protect the body from chips, hide existing damage or improve the appearance of the car. Follow this algorithm:

  1. Determine the type of thresholds:
    • 🔹 Invoices — mounted on top of standard thresholds, suitable for protection from gravel and minor scratches.
    • 🔹 Mortise — replace factory thresholds, require welding, but provide maximum protection.
  • Check compatibility: Check the year of manufacture of yours Kodiaq (pre-restyle or restyle 2021+) - the design of the thresholds may differ. For example, for Kodiaq RS special linings are needed taking into account the sports body kit.
  • Assess the condition of the body: If the thresholds are already rusty, mortise options are preferable - they allow you to remove corrosion and treat the metal from the inside.
  • Select material: For aggressive use (off-road driving), stainless steel is optimal; for the city - aluminum or plastic with an anti-gravel coating.
  • Check the package: The kit must contain fasteners, seals and instructions. For mortise thresholds, additional treatment (for example, primer) may be required.

    • - Compatible with Kodiaq model year

    - Availability of quality certificates (for example, TÜV for HEKO)

    - Complete set (fasteners, seals)

    - Manufacturer's warranty (at least 1 year)

    - Owner reviews on forums (for example, SkodaClub.ru)-->

    If you choose cut thresholds, pay attention to the thickness of the metal: for Kodiaq optimal 1.5–2 mm (thin thresholds quickly deform). Also check if it is included protective film — it prevents scratches during transportation and installation.

    Installing thresholds on the ŠKODA Kodiaq: step-by-step installation

    The installation can be done independently (for overhead thresholds) or entrusted to professionals (for mortise ones). Let's consider both options.

    Installation of overhead thresholds

    Tools required: Torx T25 wrench, screwdriver, degreaser, double-sided tape (for example, 3M VHB), sealant.

    1. Preparation: Thoroughly wash and degrease the surface of the thresholds. Remove old protection (if any).
    2. Trying on: Place the trim on the threshold and mark the fastening points. For Kodiaq Standard holes for self-tapping screws are usually used.
    3. Mount: Apply double-sided tape to the inside of the cover, then secure it with self-tapping screws. For reliability, coat the edges with sealant.
    4. Completion: Check the tightness of the fit - the gaps are more 1–2 mm unacceptable.
    💡

    Before installation, warm up the pads with a hair dryer - this will make the plastic more elastic and make installation easier.

    Installation of mortise thresholds

    This process is more complicated and requires welding. It is better to entrust it to professionals, but if you decide to do it yourself, follow the instructions:

    1. Removing old thresholds: Use a grinder to cut off the factory thresholds, leaving 10–15 mm metal for welding.
    2. Processing: Remove rust, treat the metal with a rust converter (for example, Tsinkar), then apply primer.
    3. Welding: Spot weld the new thresholds, then putty and paint. For Kodiaq It is important to maintain drainage holes!
    4. Anticorrosive: Treat the inner surface of the thresholds with an anti-corrosion compound (for example, Dinitrol).
    ⚠️ Attention: When cutting off old sills, be careful not to damage the side members - these are critical body safety elements. If you are not confident in your skills, contact a car service.
    What happens if the thresholds are welded incorrectly?

    Poor welding can lead to:

    - Corrosion at seams (due to poor sealing).

    - Body deformation during an accident (if the thresholds cannot withstand the load).

    - Problems with passing technical inspection (if the seams are visible and untreated).

    Top 5 mistakes when choosing and setting thresholds on Kodiaq

    Even experienced car owners make mistakes that ruin all efforts to protect thresholds. Let's look at the most common ones:

    • 🔴 Ignoring surface preparation. Installing scuff plates on rusty or dirty sills will accelerate corrosion. Always strip the metal to a bare state.
    • 🔴 Savings on fasteners. Cheap double-sided tape will fall off in a month, and weak screws will not withstand the load. Use only certified fasteners.
    • 🔴 Failure to maintain clearances. If the trim fits tightly to the door, over time it will begin to rub against the paint. Optimal clearance - 2–3 mm.
    • 🔴 No anti-corrosion treatment. Even stainless steel needs additional protection (for example, mastic) from the inside.
    • 🔴 Purchasing universal thresholds. Overlays “one size fits all” rarely fit perfectly. For Kodiaq look for parts marked 5N (body code).

    Another common mistake is choosing the wrong color. If you use plastic pads, keep in mind that they will fade over time. It is better to choose matte black or gray options - they are less noticeable and retain their appearance longer.

    💡

    The most dangerous mistake is installing thresholds without treating rust. Even a small area of corrosion under the lining will lead to through holes in 1–2 years.

    Review of the best thresholds for ŠKODA Kodiaq: rating 2026

    Based on owner reviews and tests by independent experts (including ADAC and "Behind the Wheel") we have compiled a rating of the best thresholds for Kodiaq:

    Model Material Features Rating (out of 5)
    HEKO 910 Aluminum Anti-gravel coating, precise fit, complete with fasteners 4.9
    Skoda Original 5N0853651/652 Galvanized steel Original, requires painting, perfect fit 4.7
    EGR KS1008 Polyurethane Flexible, do not break in the cold, budget option 4.5
    AutoStyle AS-KOD-01 Stainless steel Reinforced design, suitable for off-road use 4.8

    HEKO 910 leads due to its combination of lightness, strength and anti-corrosion properties. These thresholds do not require painting and are scratch resistant. Skoda Original Suitable for those who value a perfect fit, but are willing to pay for painting. For a budget solution EGR KS1008 — the best choice, especially if you drive mostly around the city.

    If you need thresholds for Kodiaq RS, pay attention to models marked Sportline — they take into account the features of the sports version’s body kit.

    Caring for ŠKODA Kodiaq sills: how to extend their service life

    Even the most durable thresholds require maintenance, especially in Russian conditions. Follow these guidelines:

    • 🧼 Washing: Use a touchless cleaner or a soft sponge. Avoid hard brushes - they will scratch the coating.
    • 🛡️ Protection: Apply an anti-gravel film or ceramic coating to the thresholds (for example, Ceramic Pro). This will protect against chipping and fading.
    • ❄️ Winter care: After driving on roads treated with the reagent, wash the sills with warm water. Do not use hot water as this may damage the plastic.
    • 🔧 Checking the fasteners: Once every 3 months, check the reliability of the screws and tape. If necessary, tighten the fasteners.
    • 🎨 Recovery: If scratches appear, use a repair pencil (for example, Touch-Up Paint) for metal thresholds.

    For plastic linings, it is useful to treat them once every six months silicone grease - this will prevent cracking in the cold. If the thresholds are metal, apply to the inner surface in autumn and spring. oil anticorrosive (for example, Mobil 1).

    ⚠️ Attention: Do not use products containing abrasives (for example, powders) or acids (for example, citric acid to remove rust) to clean thresholds. They destroy the protective coating.

    Frequently asked questions (FAQ)

    Is it possible to install thresholds on a Kodiaq yourself, without experience?

    Overhead thresholds can be installed - it does not require special skills. All you need is a screwdriver, degreaser and double-sided tape. It is not recommended to install mortise thresholds yourself: welding work and experience working with the body are required. Welding errors can lead to corrosion or deformation of the body.

    Which sill material is best for off-road driving?

    Optimal for off-road stainless steel thick 2 mm or aluminum with anti-gravel coating. These materials can withstand impacts from stones and branches. Plastic linings are not suitable for such conditions - they quickly crack. Also pay attention to models with additional stiffening ribs (for example, AutoStyle AS-KOD-01).

    Do original Skoda sills need to be painted?

    Yes, original thresholds Skoda Original are supplied primed and require painting. They can be painted in body color or matte black (the most practical option). If you don't paint it, the metal will quickly begin to rust. For painting, use automotive enamel with anti-corrosion primer.

    How much do door sills cost on a Kodiaq at an official dealer?

    Cost of original thresholds Skoda Original at dealership centers is 18 000–25 000 ₽ per set (excluding painting and installation). Installation will cost additional 5 000–8 000 ₽. Alternative brands (eg. HEKO or EGR) will cost less - from 3 000 ₽ for plastic covers.

    Is it possible to drive without sills if they are rotten?

    Ride without thresholds highly not recommended. Thresholds are not only protection, but also an element of body rigidity. Their absence or severe corrosion can lead to:

    • 🔹 Body deformations during an accident (passive safety decreases).
    • 🔹 Moisture and dirt entering the interior (through unprotected openings).
    • 🔹 Problems with passing technical inspection (corrosion is considered a critical defect).

    If the thresholds are rotten, they need to be cut off and new ones welded as soon as possible.