Selection of rims and tires for ŠKODA Octavia 2013 is a task that requires attention to technical details. Even a slight deviation in the bolt pattern can lead to vibrations, accelerated wear of the suspension, or the inability to install the wheel. In this article we will look at all key parameters: from standard bolt pattern 5×112 to permissible overhang values (ET) and the diameter of the central hole (DIA).

Feature Octavia second generation (including restyled versions of 2013) - unification of many parameters with other models of the concern Volkswagen Group. This opens up wide possibilities for tuning, but also requires strict adherence to the manufacturer’s recommendations. We have collected current data from official manuals, as well as the experience of owners, to help you avoid common mistakes when selecting wheels.

What is a bolt pattern and why is it important for the ŠKODA Octavia 2013

Bolt pattern (or PCD — Pitch Circle Diameter) is the diameter of the circle on which the wheel rim mounting holes are located. For Octavia 2013 this parameter is standard: 5×112. Digit 5 denotes the number of holes, and 112 - the diameter of the circle in millimeters on which they are located.

An error in bolt pattern is one of the most dangerous when selecting wheels. For example, a disk with the parameter 5×100 (like many Japanese cars) it is physically impossible to attach it to the hub Octavia, even if the holes visually match. At best, the wheel will wobble, at worst, it will fall off while driving. Therefore check PCD before purchasing, especially if you take discs from disassembly or used ones.

  • 🔧 PCD 5×112 - standard for all modifications Octavia A5 (2004–2013) and FL (facelift 2009–2013).
  • ⚠️ Incompatible options: 5×100, 5×114.3, 4×100 (even with adapters!).
  • 🔄 Exception: some sport versions (eg Octavia RS) may have unique parameters - check by VIN.

In addition to the bolt pattern, when selecting disks the following are taken into account:

  • 📏 offset (ET) — the distance from the mating plane of the disk to its center. For Octavia 2013 permissible range: from ET35 up to ET50.
  • ⭕ Center Hole Diameter (DIA) - must be no less 57.1 mm (hub standard).
  • 🔩 Mounting type - bolts M14×1.5 (thread length not less than 27 mm).
📊 What rims do you prefer for Octavia?
  • Steel stamped
  • Cast light alloy
  • Forged
  • Tuning (non-standard)

Standard wheel and tire parameters for ŠKODA Octavia 2013

The manufacturer sets strict requirements for wheel sizes depending on the configuration and engine. For example, basic versions Octavia 1.6 MPI equipped with disks 6J×15 ET45, whereas Octavia RS received 7J×17 ET51 with low profile tires. Below is a table with official data for the most common modifications.

Modification Disk size offset (ET) Tire size Pressure (bar)
Octavia 1.4 TSI / 1.6 MPI 6J×15 ET45 195/65 R15 2.2 / 2.4
Octavia 1.8 TSI / 2.0 TDI 6.5J×16 ET42 205/55 R16 2.3 / 2.5
Octavia RS (petrol/diesel) 7J×17 ET51 225/45 R17 2.4 / 2.6
Octavia Scout (crossover) 7J×17 ET38 225/50 R17 2.3 / 2.5

Important: for versions with all-wheel drive (4×4), the installation of wheels with an offset of at least ET40 is allowed - this is due to the peculiarities of the transmission.

When choosing non-standard sizes (for example, 18" disks) be sure to check:

  • 🔍 Clearance — low-profile tires can touch the arches when fully loaded.
  • ⚖️ Axle load — tire load capacity index must be at least 91T (for most versions).
  • 📊 Speedometer indicators — a change in the wheel diameter by more than 3% will lead to an error in the readings.
💡

Use online calculators to check tire size compatibility. For example, service WillTheyFit will help you avoid mistakes when upgrading disks.

How to measure bolt pattern yourself

If you buy used wheels or are in doubt about the markings, you can measure the bolt pattern yourself. You will need a caliper or ruler. Algorithm for 5×112:

  1. Measure the distance between the centers of two adjacent holes - get the value X.
  2. Multiply X by the coefficient 1.701 (for 5 holes). The result should be close to 112 mm.
  3. Check the diameter of the central hole - it should be at least 57.1 mm.

For accuracy, use the formula:

PCD = X × 1.701 (for 5 bolts)

PCD = X × 1.414 (for 4 bolts)

If you don't have any tools at hand, use bolt patterns (sold in car dealerships) or smartphone applications, for example, Wheel Fitment.

⚠️ Attention: Don't rely on visual assessment! Wheels with bolt pattern 5×110 can “sit” on the hub Octavia, but when moving this will lead to runout and damage to the bearings.

Measure PCD (should be 5×112)

Check the diameter of the central hole (minimum 57.1 mm)

Check departure compatibility (ET35–ET50)

Check the length of the bolts (at least 27 mm)

Check the tire load index with the vehicle weight -->

Compatible with other VW Group models

Thanks to the unification of the platform PQ35, wheels from a number of models Volkswagen Group suitable for Octavia 2013 without modifications. This expands the selection on the aftermarket and simplifies the search for spare parts. However, there are nuances:

  • 🚗 Full compatibility: Volkswagen Golf V/VI, Jetta, Passat B6/B7, Audi A3 8P, SEAT Leon 1P.
  • ⚠️ Partial compatibility: Audi A4 B7 (offset may vary), ŠKODA Superb II (some versions have ET48).
  • ❌ Incompatible: Volkswagen Polo (4×100), Tiguan (may require another DIA).

When purchasing disks from other models, be sure to check:

  • 📌 offset (ET) - even a difference of 5 mm can lead to wheel friction on the arch.
  • 🔧 Mounting type - some Audi use cone bolts 60°, whereas ŠKODA — spherical.
  • ⚖️ Disc weight — heavy alloy wheels increase the load on the suspension.

Example: disks from Golf GTI with parameters 7.5J×18 ET45 suitable for Octavia RS, but may require rolling out the arches when installing tires wider than 235 mm.

What happens if you install disks with the wrong ET?

Misalignment of the wheel with the hub will lead to accelerated wear of the wheel bearings and ball joints. When ET < 35 the wheel will protrude beyond the arch (risk of damage when cornering). When ET > 50 — will move inward, which may affect the suspension elements.

Tuning and non-standard sizes: what is acceptable for Octavia 2013

Many owners Octavia strive to improve the appearance of the car through large wheels and low-profile tires. However, such tuning requires taking into account technical limitations. Below are acceptable options without making changes to the design:

Disk size Minimum ET Recommended tire Notes
7J×17 ET40 225/45 R17 Standard for Octavia RS. Can be installed on basic versions.
7.5J×18 ET42 225/40 R18 Requires tires with a load index of at least 92V.
8J×19 ET45 235/35 R19 Rolling out the arches is recommended. Risk of suspension damage on bad roads.

When installing larger drives 18" consider:

  • 🛠️ The need to roll out arches — without it, the tires may rub when fully loaded or sharp turns.
  • 📉 Deterioration in comfort — low-profile tires transfer all road irregularities to the suspension.
  • 💰 Tire cost - tires for 19" Discs will have to be changed more often due to the lower tread height.

For sports versions (RS) departure is allowed until ET35, but this requires installing spacers or modifying the suspension. Without proper preparation, such tuning is dangerous!

💡

Increasing the wheel diameter by more than 2 inches from the standard requires recalculating the tire load index and checking compatibility with ABS/ESP.

Typical mistakes when selecting disks and how to avoid them

Even experienced car owners sometimes make mistakes when choosing wheels for Octavia. Here are the most common ones:

  1. Ignoring offset (ET). Discs with ET30 may look stylish, but will move the wheel axle outward, increasing the load on the wheel bearings.
  2. Purchasing disks with the wrong DIA. Centering through adapter rings is unreliable - during emergency braking, the disc may move.
  3. Saving on bolts. The use of bolts is shorter 27 mm or with incorrect thread (M12 instead of M14) will lead to weakening of the fastening.

To avoid problems, follow the checklist:

Check PCD (must be 5x112)

Make sure DIA ≥ 57.1 mm

Reach (ET) in the range of 35–50

Bolts M14×1.5 length ≥ 27 mm

Tires with load index ≥ 91T-->

Pay special attention winter tires. For Octavia 2013 recommended size - 205/55 R16 or 195/65 R15. Narrow tires handle snow better, but don’t forget about the speed index: optimal for Russia T (190 km/h) or H (210 km/h).

⚠️ Attention: Installing tires with a lower speed index T (for example, Q) voids the insurance coverage in case of an accident at a speed above 160 km/h.

Where to buy wheels for ŠKODA Octavia 2013: new vs used

The market offers many options - from original discs ŠKODA to replicas and used copies. Let's look at the pros and cons of each option:

Disc type Pros Cons Average price (per set)
Original (ŠKODA/VW) Guaranteed compatibility, high quality High cost, limited design from 80,000 rubles
Cast (Replica) Large selection of designs, affordable price Risk of low quality (especially for no-name brands) from 30,000 rubles
Forged Lightweight, durable, suitable for tuning Dear ones, limited range for Octavia from 120,000 rubles
Used (from disassembly) Low price, original wheels Risk of hidden defects (cracks, corrosion) from 15,000 rubles

When purchasing used disks, be sure to:

  • 🔍 Check for cracks - especially around bolt holes.
  • ⚖️ Make sure there is no deformation — rolling on a machine does not always restore the geometry.
  • 🧲 Use a magnet - if the disk is not magnetic, it may be low quality aluminum.

To purchase new discs, we recommend official dealers or trusted online stores:

  • 🌍 KolesaDarom - wide range of replicas.
  • 🌍 Exist.ru - original wheels and analogues.
  • 🌍 Autodoc — convenient selection by car model.
💡

When purchasing wheels online, always check to see if the set includes a set of bolts and centering rings (if needed).

FAQ: Frequently asked questions about the ŠKODA Octavia 2013 bolt pattern

Is it possible to install 5x100 wheels on Octavia 2013?

No, this is not possible without adapters. Bolt pattern 5×100 incompatible with 5×112 — the holes will not match, and the use of adapters is dangerous (risk of the wheel coming off while driving).

What is the maximum disk size that can be installed without modifications?

For most versions - 18" with departure ET42–45. For Octavia RS allowed 19", but will require rolling out the arches and low-profile tires.

What happens if you install wheels with an offset of ET30?

The wheel will move outward, which will increase the load on the wheel bearings and may cause the tire to rub against the arch. Acceptable minimum - ET35 (only for sports versions).

Will wheels from Passat B7 fit Octavia 2013?

Yes, but check the departure. U Passat B7 he might be ET48–50, which is acceptable for Octavia. Also make sure that the diameter of the center hole is not less than 57.1 mm.

What is the tire pressure for Octavia 1.6 MPI?

Recommended pressure: 2.2 bar front and 2.4 bar back for sizes 195/65 R15. When fully loaded, increase to 2.5 bar.