ŠKODA Superb: A Complete Guide to Range and Wheel Parameters

Selecting disks for ŠKODA Superb - a task that requires attention to technical details. Error in bolt pattern parameters (PCD) or departure (ET) can lead to vibrations, accelerated wear of the suspension, or even an emergency situation. This article will help you understand the nuances of bolt patterns for all generations. Superb - from the first B5 (1996–2008) until relevant B8 (from 2023).

We collected the official data of the manufacturer, compared them with real-life tests of owners and added practical tips for the selection of discs. Particular attention was paid to compatibility with winter tires, the impact of offset on handling and how to avoid typical mistakes when buying. If you are planning to replace the wheels Superb Or just want to check the current parameters – this information will be useful.

What is a bolt pattern and why is it important for the ŠKODA Superb

Bolt pattern (or PCD - Pitch Circle Diameter) is the diameter of the circle on which the holes for attaching the disc to the hub are located. For ŠKODA Superb This parameter is standardized, but may vary depending on generation and modification. For example, Superb B6 (2008–2015) Blur 5×112, and Superb B8 - the same, but with other tolerances for offset and diameter of the central hole.

A mismatched bolt pattern leads to:

• 🔧 Disk landing incorrectly Even if the bolts are screwed, the disc will be displaced relative to the hub, which will cause a beat.
• 🚗 Accelerated wear wheel bearings and suspension elements due to uneven load.
• ⚠️ Loss of warranty If the disc is not certified for your model, the dealer may refuse warranty repairs.

Except PCDWhen selecting discs, it is important:

• 📏 offset (ET) — the distance from the mating plane of the disk to its center. For Superb usually varies from ET35 up to ET50.
• ⭕ Center Hole Diameter (DIA) - must match the diameter of the hub or be larger (using adapter rings).
• 🔩 Fastener type - for Superb bolts are used M14×1.5 (less often M12×1.5 for older models).

⚠️ Attention: Discs with infidels PCD They can sit on the hub crooked, even if the bolts spin. This will cause imbalance and vibrations at speeds above 80 km/h. Always check the slap before buying!

Bolt pattern table for ŠKODA Superb by generation

Below are the official bolt pattern parameters for all generations ŠKODA Superb, including data for all-wheel drive modifications (4×4) and sports versions (Sportline/RS). Please note that for some years of release, the parameters may differ – check them in the operating manual.

Generation	Years of manufacture	Bolt Pattern (PCD)	Reach (ET), mm	DIA, mm	Bolt thread
Superb B5 (Typ 3U)	1996–2002	5×100	ET35–ET45	57.1	M12×1.5
Superb B5 FL (Typ 3U)	2002–2008	5×112	ET38–ET48	57.1	M14×1.5
Superb B6 (Typ 3T)	2008–2015	5×112	ET35–ET50	57.1	M14×1.5
Superb B7 (Typ 3V)	2015–2023	5×112	ET30–ET45	57.1	M14×1.5
Superb B8 (Typ 3V)	from 2023	5×112	ET28–ET42	57.1	M14×1.5

Important: For models with all-wheel drive (4×4), it is allowed to use disks with a offset ET30-ET35, but not lower! Installing discs with ET<30 may cause the inner side of the disc to be touched by the suspension elements.

If your car is equipped with a sports suspension (Sportline or RSCheck the flight separately – it can be reduced by 5-10 mm to improve handling. For example, for Superb RS B7 recommended flight - ET35.

How to measure the bolt pattern on a ŠKODA Superb yourself

If you are not sure about the parameters of your car or are buying used wheels, you can measure the bolt pattern yourself. For this you will need:

• 📏 Ruler or caliper (more precisely).
• 🔧 A key for unscrewing the wheel (if you need to remove the disk).
• 📝 Paper and pen for notes.

Step 1. Count the number of holes

U Superb 5 holes under the bolts, but on some modifications (for example, B5 before 2002) could be used PCD 5×100. Make sure that there are 5 holes, not 4 or 6.

Step 2. Measure the distance between the centers of the neighboring holes

For PCD 5×112 The distance between the centers of two adjacent holes should be 70.5 mm (calculated by the formula: PCD × sin(180°/5)). For 5×100 It's a value. 61.8 mm.

Step 3. Check the diameter of the central hole (DIA)

Everyone. Superb (except B5 before facelift DIA = 57.1 mm. If the hole in the disk is larger, use transition rings (see below).hubs).

⚠️ Attention: Some sellers indicate the bolt pattern as 5/112 or 5-112 - it's the same as 5×112. However, avoid discs with universal bolt pattern (for example, 5×112/5×114.3) - they often have a backlash and do not provide accurate landing.

Disc compatibility between Superb generations

Can I put the discs on the Superb B6 on Superb B8? The answer is yes, but with reservations. All generations, beginning with B5 FL 2002, have the same squabbling 5×112but differ in:

• 🔄 offset (ET) - for example, discs with B6 (ET45) on B8 (ET30) the wheel is extended outwards, which may result in the arch being touched.
• ⚙️ Disc width - wider discs (e.g., 8.5J instead of 7J) require tyres with a smaller profile.
• ❄️ Compatibility with winter tires - on B8 It is recommended to use disks with ET≥35 for the installation of winter tires.

Compatibility examples:

• ✅ Discs with Superb B7 (ET38, 7.5J) suitable for Superb B6They can extend beyond the arch by 5-10 mm.
• ❌ Discs with VW Passat B6 (5×112, ET50) are not suitable for Superb B8 Sportline Too much flight will worsen the handling.

If you are planning to use a disc from another model VW Group (for example, Audi A6 or VW Arteon), check not only PCD, but also:

• 📌 Center distance - y Superb and Audi It may be different, which will affect the life of the suspension.
• 🔧 Hub type Some drives require inserts or adapters.

Impact of overhang (ET) on handling and safety

Departure (ET) is one of the most critical parameters in the selection of discs. It determines how much the wheel will be "sunk" in the arch or, conversely, protrude outwards. For ŠKODA Superb recommended values:

• 🚗 Standard versions: ET35–ET45.
• 🏁 Sportline/RS: ET30–ET38 (for better handling).
• ❄️ Winter tires: ET≥35 (to prevent the suspension from touching).

What happens if you install the disks with the wrong departure?

ET deviation	Consequences	Risks
ET < recommended (for example, ET25 instead of ET35)	The wheel protrudes behind the arch, the track increases.	Touching the arch when cornering, accelerated wear of hub bearings.
ET > Recommended (for example, ET50 instead of ET38)	The wheel "drows" in the arch, the track decreases.	Deterioration of handling, the risk of touching the inner side of the disk on the suspension elements.

For example, if on Superb B7 install disks with ET20 (instead of recommended) ET35), then:

• 🔧 When the car is fully loaded, the wheel will touch the arch on the bumps.
• 📉 The load on the hub bearing will increase, which will reduce its life by 30-40%.
• 🚦 At speeds above 120 km / h, a yaw (instability in straight-line movement) may appear.

How to check the flight without special tools?

If you do not have a caliper, you can approximately measure the offset using a ruler and level. Place the disc on a flat surface (for example, on glass), then apply the ruler vertically to the rim. Measure the distance from the surface to the landing plane (where the disc is attached to the hub). Divide this value by 2 and get an approximate flight. For example, if the distance is 70 mm, then ET≈35.

⚠️ Attention: Some workshops offer to "fit" the flight with the help of paddles. It's dangerous! The slings increase the load on the hub and can cause the wheel to break off at high speed. If the flight is not suitable, look for other disks.

Selection of tires for rims on the ŠKODA Superb

Spoiling and relegation are not the only parameters to consider. It is equally important to choose the right tires, so that they correspond to the width of the disk and do not worsen the characteristics of the car. For Superb The following recommendations apply:

Disc width (J)	Recommended tire width (mm)	Size example
6.5J	195–215	205/55 R16
7J	215–235	225/45 R17
7.5J	225–245	235/40 R18
8J	235–255	245/35 R19

When choosing tires, consider:

• 🌡️ Seasonality - for winter, choose tires already by 10-15 mm (for example, 205/60 R16 instead of 225/50 R17).
• 📏 Profile - the lower the profile, the tougher the suspension and the higher the risk of damage to the disk on the pits.
• 🔄 Load Index - for Superb it should be no lower 91T (615 kg per wheel).

For example, for Superb B8 with disks 8J×19 ET35 The optimal tyre size. 235/35 R19. If you put 255/30 R19, then:

• ✅ Dry asphalt grip will improve.
• ❌ The risk of water planning on wet roads will increase.
• ⚠️ You may need to roll out the arches (on the sports versions).

Typical mistakes when choosing wheels for the ŠKODA Superb

Even experienced car owners sometimes make mistakes when selecting wheels. Here are the most common ones and how to avoid them:

1. Ignoring the DIA parameter (central hole)

Many people think that if PCD and ET match, the disc will do. However, if DIA The disk is smaller than the hub, it will not be possible to install. If more, transition rings will be required.hubs) which must be made of aluminum (not plastic!).

2. Buying discs with universal bolt pattern

Discs with markings 5×112/5×114.3 They have elongated holes under the bolts, which leads to:

• 🔧 The sleeve is then slapped (even if the sleeves are tight).
• 🚗 Vibrations at speeds above 100 km/h.
• ⚠️ Risk of self-unscrewing of bolts.

3. Non-reporting disc weight

Forged or cast discs can weigh 2-4 kg less stamped, which improves dynamics and reduces fuel consumption. However, too light discs (less than 7 kg for the R17) may not withstand the load when it enters the pit.

4. Neglecting balancing

Even new discs require balancing! An unbalanced wheel at 120 km/h creates a load equivalent to a 3 kg hammer hitting the suspension every 2 seconds.

5. Installation of discs with inappropriate bolt thread

For Superb (except B5 until 2002) bolts are used M14×1.5. Bolts M12×1.5 or M14×1.25 They will not be able to do so, or they will not be able to do so.

FAQ: Frequently asked questions about the ŠKODA Superb bolt pattern

Can I put 5x100 discs on the Superb B6?

No, this is not possible without adapters. Bolt pattern 5×100 used in older models VW Golf and ŠKODA Fabiabut not compatible with Superb B6 (5×112). Adapters for change PCD They are not recommended, they worsen security.

What is the maximum offset can be put on the Superb B7 with all-wheel drive?

For Superb B7 4×4 maximum reach - ET45. Installing disks with ET50 and above will lead to touching the inner side of the disk about the suspension elements at full load of the car.

Will Audi A6 drives fit the Superb B8?

Yes, but with reservations. U Audi A6 C7/C8 bolt pattern 5×112, ET35–ET45 and DIA 57.1 - like Superb B8. However:

• Discs with Audi S6 may have overhang ET25which is not suitable for Superb.
• Some disks Audi have a unique mount for pressure sensors (TPMS) that are not compatible with ŠKODA.

What happens if you don't use the transition rings at DIA 66.6 instead of 57.1?

The disc will sit on the hub not in the center, but with a shift. This will lead to:

• 🔧 Steering wheel wobble at speeds above 60 km/h.
• 🚗 Uneven tire wear.
• ⚠️ Risk of damage to the hub under heavy load (for example, when falling into a hole).

Transition rings (hubsThey are inexpensive (from 300 rubles) and must be installed!

Can I play ET20 on Superb Sportline?

Technically yes, but it's not recommended. Departure ET20 It pushes the wheel outwards, which leads to:

• Increased load on wheel bearings (lifetime is reduced by 40–50%).
• Risk of touching the arch when fully loaded or making sharp turns.
• Deterioration in handling at high speed (the car becomes “nervous”).

For Sportline optimal flight - ET30–ET35.