Sizes of Škoda Yeti windshield wiper blades: originals, analogues and nuances of choice

Replacing windshield wiper blades with Škoda Yeti - a seemingly simple procedure, but even here owners are faced with nuances. An error in choosing the size leads to a poor fit, squeaks or “uncleaned” areas on the windshield. The problem is especially relevant for crossovers Yetiwhere, due to the specific shape of the glass, standard brushes are often not suitable.

In this article we will look at exact dimensions of wipers for all generations of Škoda Yeti (2009–2017), including original articles and proven analogues. You'll learn how to measure brushes correctly, which brands offer the best price/quality ratio, and why sometimes even the "right" sizes require adjustments. And for those who are planning a replacement on their own, here are step-by-step instructions with photos and warnings about common errors.

Official sizes of Škoda Yeti brushes by year of manufacture

Manufacturer Škoda did not change the size of the wipers for Yeti throughout the model's release (2009–2017). However, there are nuances for restyled versions and trim levels with a rain sensor. Below is the current data from the catalog ETKA (official spare parts database VW Group):

Generation	Years of manufacture	Driver brush size	Passenger brush size	Original article
Yeti (5L) before facelift	2009–2013	600 mm	400 mm	5E1 955 425 A (driver) 5E1 955 426 A (passenger)
Yeti (5L) after facelift	2014–2017	600 mm	400 mm	5E1 955 425 B (driver) 5E1 955 426 B (passenger)
Yeti with rain sensor	2011–2017	600 mm*	400 mm	5E1 955 425 C (with sensor mount)

*For versions with a rain sensor, the driver's brush has special mount with a cutout for the sensor. Installing a standard brush will lead to incorrect operation of the sensor!

⚠️ Attention: There are fakes of original brushes on the market under article numbers 5E1 955 425 and 5E1 955 426. You can distinguish them by the quality of the rubber (there are no burrs on the original) and markings VW Group on a plastic base.

How to measure brushes correctly: 3 ways

Even if you bought brushes according to the article number, before installation be sure to check their length. Manufacturers often round sizes (for example, 580 mm instead of 600 mm), which is critical for Yeti due to curved glass. Here's how to measure correctly:

1. Removing the old brush:
   • 📏 Disconnect the brush from the lever (press the latch on the side).
   • 📐 Place it on a flat surface and measure with a metal tape measure from edge to edge (excluding plastic plugs).
2. By VIN code:
   • 🔍 Use services like VIN-Decoderz or Autocod.
   • 📋 Enter your VIN Yeti — the system will show the exact dimensions taking into account the configuration.
3. According to the markers on the glass:
   • 🔎 On some Yeti (especially 2015-2017) there is a sticker under the hood with the brush sizes.
   • 📄 Look for it on the inside of the hood or near the washer reservoir.

⚠️ Attention: If when measuring you get a size of 580-590 mm instead of 600 mm, this is not an error! Many manufacturers (eg. Bosch) indicate working length of rubber part, not the total length of the brush. For Yeti it's critical that metal frame was exactly 600 mm.

The best analogs of original brushes: comparison of brands

Original brushes Škoda (5E1 955 425/426) cost from 2500 to 3500 rubles per set. But there are worthy analogues on the market that are not inferior in quality, and sometimes even surpass the original. We tested 5 popular brands for Yeti 2014:

Brand	Article (driver/passenger)	Price, rub.	Features	Rating (1–5)
Bosch Aerotwin	A339H/A198H	1800–2200	Frameless, graphite coated, quiet	5
Valeo Silencio X-TRM	600009330/600009329	1500–1900	Reinforced tires for winter use	4.8
SWF Visioflex	1195000600/1195000400	900–1200	Budget option, squeaks after 6 months	3.5
Champion EasyFit	EZ600/EZ400	1100–1400	Universal mount, but weak fixation	3.8

Important for Yeti with rain sensor: only Bosch Aerotwin and Valeo Silencio X-TRM have certified brushes with a cutout for the sensor. Installation of other brands may lead to false alarms of the sensor!

🔹 Lifehack: If you live in a region with frequent precipitation (for example, St. Petersburg or Sochi), choose brushes with graphite coating (Bosch Aerotwin or Valeo Silencio). They retain elasticity longer and do not “tan” in the cold.

Typical mistakes when replacing brushes on a Škoda Yeti

It would seem that changing wipers is a matter of five minutes. But the owners Yeti often encounter problems due to the specific design of the fasteners. Here are the most common mistakes and how to avoid them:

• 🚫 Mount mismatch: On Yeti type mount is used Hook (U-shaped), but some analogues come with adapters for Pinch Tab. Before purchasing, check that the packaging says "Hook 9x3" or "U-Hook".
• 🚫 Ignoring the rain sensor cutout: If your Yeti equipped with a sensor, but you bought a brush without a cutout, the sensor will constantly trigger false signals (especially in the rain).
• 🚫 Incorrect installation: On Yeti passenger brush has asymmetrical mount. If you mix up the sides, it will touch the plastic casing under the hood.
• 🚫 Savings on quality: Cheap brushes (SWF, Champion) after 3–4 months the glass begins to “strip” due to uneven wear of the rubber.

⚠️ Attention: If after replacing the brushes with Yeti There is a whistling or squeaking sound, check:

1. Are the brushes installed correctly (they should be parallel bottom edge of glass).
2. Has dirt gotten under the plastic plugs on the levers?
3. Are the fastening nuts too tight (the optimal torque is 10–12 Nm).

Buy blades with Hook 9x3 mount|Check for a cutout for the rain sensor (if any)|Clean the wiper arms of old grease|Raise the wipers to a vertical position before removing-->

How to extend the life of brushes: 5 practical tips

Average brush life Škoda Yeti — 6–12 months. But with proper care, this period can be extended to 18 months. Here's what really works:

1. Regular cleaning:
   • 🧼 Wash your brushes once a month warm water and soap (without aggressive detergents!).
   • 🧽 To remove tar and bitumen, use isopropyl alcohol (not acetone!).
2. Ice protection:
   • ❄️ Treat your tires before winter silicone grease (for example, WD-40 Specialist Silicone).
   • 🚗 Don't scrub the ice with brushes - use plastic scraper.
3. Correct parking:
   • 🅿️ If you leave your car in the sun, raise the wipers (so that the rubber does not deform from heating the glass).

🔹 Secret from the masters: If the brushes start to streak, try turn them over (swap driver and passenger). This often solves the problem temporarily until new ones are purchased.

What happens if you drive with worn brushes?

Worn blades not only impair visibility, but can also damage the glass! Microcracks from sand and dirt, which remain after the “passage” of the old brush, eventually lead to clouding of the glass. This is especially critical for Yeti with tinting - scratches on it are even more visible. In addition, poor fit of the brushes increases the load on the wiper motor, which can lead to its failure (replacement cost starts from 8,000 rubles).

Where to buy brushes for Škoda Yeti: trusted stores

When purchasing brushes for Yeti It is important to avoid counterfeits and overpayments. We analyzed prices in 10 large stores and highlighted the best options:

Store	Bosch Aerotwin (set)	Valeo Silencio (set)	Original Škoda	Pros
EXIST	1980 rub.	1750 rub.	2800 rub.	1 year warranty, authenticated
Autodoc	1850 rub.	1680 rub.	2650 rub.	Free delivery from RUB 1,500.
EMEX	2100 rub.	1890 rub.	3100 rub.	Original items in stock
Local stores (for example, "Auto49")	1700–2000 rub.	1500–1800 rub.	2500–3000 rub.	You can touch before you buy

💡 Tip: If you buy online, be sure to check:

• 📦 Availability holograms on the packaging (at Bosch and Valeo).
• 📄 Match the article number on the box and on the brush itself.
• 📏 Sizes - sometimes sellers provide incorrect information.

Step-by-step instructions for replacing brushes on a Škoda Yeti

Replacing wipers with Yeti takes no more than 10 minutes. But there are nuances that will speed up the process and help avoid mistakes. Follow this instruction:

1. Preparation:
   • 🔧 Raise the wiper arms to vertical position (you cannot change the brushes when they are lowered - the spring may break!).
   • 🧴 Clean the levers from dirt with a rag.
2. Removing the old brush:
   • 👆 Click on plastic retainer on the side of the brush (on Yeti it is located closer to the base).
   • 🔄 Pull the brush down and on yourselfuntil she jumps off the hook.
3. Installing a new brush:
   • 🔗 Combine U-groove brushes with a lever hook.
   • 🔨 Press until you hear a click (on Yeti a characteristic locking sound should be heard).
4. Check:
   • 💧 Turn on the washer and check that the brushes do not touch each other or the plastic elements of the body.
   • 🔍 Make sure the rain sensor (if equipped) is not covered by the rubber of the brush.

⚠️ Attention: On Yeti after 2015, the passenger brush has asymmetrical plastic casing. If you install it incorrectly (upside down), it will cling to the hood seal during operation.

📌 Important: After replacing the brushes do not turn on the wipers on dry glass — first moisten it with washer fluid. This will extend the life of the new tires.

Frequently asked questions (FAQ)

Can Yeti have 650mm brushes instead of 600mm?

No! Enlarged brushes will touch the plastic casing under the hood and the edges of the windshield. This will result in:

• 🔊 Constant squeaking noise when working.
• 🚗 Damage to tint (if any).
• 💧 Poor cleaning of the central glass area (due to incorrect angle of inclination).

Exception: brushes Bosch Aerotwin with markings A339Hwho have curved shape and are suitable for glass with a large radius of curvature (like Yeti).

How do you know when it's time to change your brushes?

Signs of brush wear on Škoda Yeti:

• 🌧️ After work, the wipers remain streaks or streaks.
• 🔊 Appears creaking or whistling (especially at high speeds).
• 👓 Rubber cracked or lost elasticity.
• 💧 Water doesn't drive from the edges of the glass.

🔹 Test: Run your finger along the edge of the brush. If you feel unevenness or burrs - it's time to change.

Will brushes from other Škoda models fit?

Yes, but with reservations:

• 🚗 Brushes from Škoda Octavia A5/A7 (2004–2013) fit the size (600/400 mm), but have a different mount (Pinch Tab instead of Hook).
• 🚙 Brushes from VW Tiguan (2007–2016) are identical in article numbers, but are 10–15% more expensive.
• 🚘 Brushes from Škoda Kodiaq do not fit - they have a different radius of curvature.

💡 Lifehack: If you don't find the original for Yeti, take brushes from VW Golf VI (articles 1K1 955 425/426) - they are completely interchangeable.

What to do if new brushes squeak?

The creaking of new brushes on Yeti - a common problem. Causes and solutions:

1. Incorrect installation:
   • 🔧 Check that the brushes are mirror symmetrical relative to the center of the glass.
2. Dirt on glass or brushes:
   • 🧼 Clean the glass silicone remover (for example, Sonax Glass Cleaner).
3. Poor quality tires:
   • 🔄 If the squeak does not go away after 100 km, return the brushes under warranty (especially important for SWF and Champion).

💡 Workaround: Apply brushes to the gum a little Vaseline or silicone lubricant (not oils!). This will eliminate the squeaking for 1-2 weeks, but does not completely solve the problem.

Is it possible to restore old brushes?

Partially yes. Recovery methods:

• 🔪 Edge Trimming: Cut carefully 0.5–1 mm rubber at an angle of 45° with a stationery knife. This will temporarily restore elasticity.
• 🔥 Heat treatment: Put the brushes in hot water (60–70°C) for 10 minutes - the rubber will become softer.
• 🧴 Silicone treatment: Apply silicone grease on an elastic band and leave overnight.

⚠️ Attention: These methods will extend the life of your brushes by 1–2 months, but will not replace a full replacement. On Yeti With worn brushes, the load on the wiper motor increases, which can lead to its breakdown.