Remake windows ŠKODA Octavia A5: how to choose and replace yourself

Skoda Octavia A5 (2004–2013) is one of the most popular models of the Czech brand, but even it wears out the windows over time. Screaming, slowed glass movement or complete failure are typical symptoms that signal the need for repair. In 80% of cases, the problem is solved by replacement. window-lifterNot buying a new setup. This saves up to 70% of your budget if you do your own work.

In this article, we will discuss how to choose the right remake for Octavia A5What articles of original and analog parts exist, and also give step-by-step instructions for replacement, taking into account the nuances of the design. We'll put a special emphasis on common mistakeswhich lead to the re-incapacity of the mechanism in 1-2 months.

Signs of malfunction of the window lifter: when you need a remap

The first “bells” about problems with the window are often ignored until the windows stop moving altogether. Here are the key symptoms for which reset is already needed:

• 🔊 Creaking or crunching when moving glass - a sign of wear of plastic guides or cable.
• 🐢 Slow-motion rise/lowering glass (more than 5 seconds at full speed) - a signal about the stretching of the cable or corrosion of rollers.
• ⚡ Glass "jumps" or jams in extreme positions - a problem with the fixers or deformation of the rope.
• 🚫 Complete refusal (glass does not respond to a button) – often caused by a cable break or motor failure (but check the fuse first) F30 at 30A).

If at least one of these signs manifested, you should not delay the repair. Worn cable can break at any time, leaving the glass in the semi-open position - and this is the risk of moisture entering the cabin and corrosion of the door. By the way, on Octavia A5 Most often windows break down front doors (especially the driver) because they are used more intensively.

⚠️ Attention: If the glass has fallen into the door and is not fixed in the upper position, do not try to lift it manually - this can deform the guides. It is better to immediately remove the skin of the door and fix the glass with tape until you replace the remake.

Article numbers of repair kits for Skoda Octavia A5: original vs analogues

On Octavia A5 There were two types of windows: cable (on most trim levels) and rack and pinion (less commonly, mostly on models with electric packages) Highline). The remixes are not interchangeable for them! Below is a table with articles for cable mechanisms (the most common version).

Manufacturer	Article	Applicability	Average price, rubles
Skoda (original)	1Z1 837 701 A / 1Z1 837 702 A	Front left/right door	4 500–6 000
Febi (Germany)	27320 / 27321	Left/right side	2 800–3 500
Hutchinson (France)	133075	Universal (left/right)	2 200–2 700
Kavo (Poland)	KV-1018 / KV-1019	Left/right side	1 800–2 300

Original remakes Skoda They come with metal rollers and reinforced cable, but their price is often unjustified. Analogues from Febi or Hutchinson They are no worse when installed correctly. The main thing is to check the complete set when buying: in the box should be cable, 2-3 rollers, plastic guides and fasteners.

For rack windows (original article - 1Z1 837 715) remixes are less common. Here, more often change the mechanism in the assembly or restore the gears. If you are not sure about the type of window, look at the inside of the door: the cable mechanism has a visible cable in a plastic braid, and the rack has a metal gear rail.

Replacement tools: what you need besides the remake

Replacement of the windows with Octavia A5 does not require specialized equipment, but without the right tools the process can take a long time. Here's the full list:

• 🔧 Socket set (required with head on) 10 mm for the bolts of the fixing mechanism).
• 🔨 Plastic mounting blades (To remove the door paneling without damage).
• 🔩 T25 screwdriver (For the sleeves and the sleeves of the sleeves).
• 🧲 Magnetic holder (so as not to lose the bolts in the door).
• 🛠️ Coding lubricant (for example, LIQUI MOLY Silicone-Fett or CRC 2-46).
• 📸 Smartphone (To photograph the location of the parts before disassembly)

Also prepare masking tape to fix the glass in the raised position and rags There is always dust and dirt inside the door. If you plan to work in a garage, take a carry-on with a lamp: the lighting in the door is usually insufficient.

⚠️ Attention: Do not use metal screwdrivers to tweak clips of the skin - they break! Just plastic shoulder blades. Clips for Octavia A5 can be purchased separately (item no. 1J1 868 241~50 rubles / pc, but it is better to keep the relatives.

Step by step: how to replace the window lifting remake

The replacement process takes 2-3 hours at the first experience. The main thing is not to rush and follow the algorithm. Below is an instruction for sliding-glass (The back door is similar, but access is more difficult.)

Step 1: Removing the door trim

Unscrew the screw under the decorative plug of the door handle (plug it with a shovel) and a screw in the bottom of the skin. Carefully pull the skin over yourself, starting at the bottom corner - clips should come out effortlessly. Disconnect the speaker connectors and the windowshop control unit (remember their location!).

Step 2. Dismantling the mechanism

Remove the plastic protection (it is attached to 3 clips). Unscrew 3 bolts of the window lift mount (head on the 10 mm). Reduce the nuts of the mounting glass to the mechanism (do not remove completely!). Carefully remove the cable from the guides and remove the mechanism.

Step 3. Replacement of cable and rollers

Disassemble the old mechanism by removing the locking rings from the rollers. Move the metal parts (if they are in good condition) to the new remake. Set the rollers so that their grooves coincide with the guides on the door - this is critical for smooth running! Lubricate the cable and rollers with silicone lubrication.

Step 4. Assembly and testing

Set the mechanism in reverse sequence. Before final assembly, check the windows by connecting the power connector. If the glass moves in jerks, check the tension of the cable and the position of the rollers.

What if the glass is not moving evenly after replacement?

This is usually caused by improper tension of the cable or skewed rollers. Remove the mechanism and check:

1. The rollers should rotate freely, without backlash.

2. The cable should not sag or be too stretched (optimal deflection is 3-5 mm).

3. The guide glazing shall be clean and lubricated.

If the problem remains, perhaps worn out plastic bushings guides - they also need to be replaced (article) 1Z1 837 717).

Typical mistakes when replacing a repair kit and how to avoid them

Even experienced car owners sometimes make mistakes that lead to repeated repairs. Here are the most common:

1. Wrong cable tension. If the cable is pulled, the glass will move with effort; if not stretched, it will slip. Optimal tension: when manually rolling, the cable should not sag more than 5 mm.
2. Ignoring lubrication. A new cable without lubrication will last a maximum of a year. Use it. silicone grease — it does not attract dust and does not thicken in the cold.
3. Confused left/right sides. Remixes for the left and right doors mirror! There is usually a label on the packaging. L (left) or R (right).
4. Damage to wiring. When removing the skin, it is easy to hook the wires of the control unit. Turn off the battery before work!

Another common problem is squeak after replacement. It occurs if you do not clean the guide glass from the old lubricant or install rollers with backlash. Use it for cleaning. WD-40 And the slack is removed by the selection of washers.

Cost of work in the service vs self-repair

If you are not sure of your abilities, you can contact the service. However, the price of replacing the windows Octavia A5 often overpriced. Here are the approximate prices:

Type of work	Cost (rubles)	Time (hours)
Repair kit replacement (1 door)	2 500–4 000	1,5–2
Replacing the window lift assembly	4 000–6 500	2–3
Fault diagnosis	500–1 000	0,5

When you repair yourself, your costs will be limited to the cost of the remake (from 1,800 rubles) and lubricant (~300 rubles). Savings of up to 3,000 rubles per door! However, if you do not have experience with autoelectrics, it is better not to take risks: improper connection of connectors can disable the windows control unit (the price of a new one is from 8 000 rubles).

The average service life of the remaplet with proper installation - 3–5 years. If the windows started creaking again after a year, it is likely that one of the mistakes described above was made.

FAQ: answers to frequently asked questions

Can I restore an old cable instead of buying a remake?

Theoretically yes: the cable can be cleaned of rust and lubricated. But in practice, it is already stretched and worn out, so it will not last long. Remake with a new rope and rollers - a more reliable solution.

How do you know if the motor is out, not the cable?

If you press the button heard the sound of the working motor, but the glass does not move - the problem is in the cable or rollers. If the engine does not make sounds, check the safety lock. F30 and power on the connector. The motor rarely breaks on its own (original article) 1Z1 955 257).

Do I need to adjust the glass after replacing the remplekt?

Yes, but usually 1-2 full opening/closing cycles are enough. If the glass "walks" up and down, loosen the bolts of the glass attachment to the mechanism and adjust its position, then tighten the bolts.

Is the repair kit suitable for VW Golf 5 or Audi A3 8L?

Yes, these models are built on the platform PQ35, as well as Octavia A5. The articles of the rempleks are the same, but specify the side (left/right) and the type of mechanism (trail/rack).

What should I do if after replacement the glass does not rise all the way?

Most likely, the cable is not stretched enough or twisted. Remove the mechanism and check:

• The casters should be set mirror (grooves up!).
• The cable should not overcoat.
• The glass should move freely in the guides without jamming.