Crossover owners Skoda Yeti Often faced with the need to access the insides of the front panel. This may involve replacing the cabin filter, eliminating unpleasant creaks, or installing additional equipment such as a backlight or fuse unit.
The process of dismantling the crate on this model has its own characteristics that differ from other cars of the VAG group. Incorrect actions can lead to breakage of plastic latches or damage to the skin of the dashboard. Therefore, it is important to act consistently and with an understanding of design.
In this article, we will discuss in detail how to remove the glove compartment on Skoda Yeti without unnecessary tools and risks to the car. You will learn about hidden bolts, mounting tricks and build nuances that beginners often miss.
Preparing tools and workspace
Before any manipulations with the interior of the car must be prepared appropriate inventory. In most cases, you wonβt need a sophisticated professional set, but having certain tools will speed up the process.
The main tool for the work will be a cross screwdriver, preferably with a magnetic tip, so as not to lose screws in hard-to-reach places. Also useful plastic blade or mount for careful snapping of the fixers without scratches.
- π§ Cross screwdriver PH2 (medium)
- π§ Set of plastic spatulas for removing panels
- π§ Flashlight for illuminating internal cavities
- π§ Soft fabric to protect surfaces
The workspace should be well lit, especially if you plan not only to remove the drawer, but also to perform further work. Make sure there are no sharp objects nearby that can scratch a dashboard or seat when randomly moving.
It is recommended to turn off the battery's negative terminal if you plan to work with the backlight wiring or fuses located behind the box. This will eliminate the risk of short circuit during dismantling.
Finding and unscrewing hidden fasteners
Construction Skoda Yeti provides several points of attachment of the cloth box, which are not always obvious at first glance. The main mistake of beginners is to try to pull the box out by force, without finding all the fixing screws.
First of all, you need to open the glove compartment itself and carefully examine its interior. At the top of the side walls are usually two screws, covering plastic plugs or available immediately. They need to be carefully twisted.
The next step is to find the lower mounts. Often they are hidden behind decorative overlays or located in the depths of the opening. To detect them, a flashlight and a mirror on a flexible handle may be required.
- π Inspect the upper corners of the inner compartment
- π Check for the presence of plugs under the screws in the lower part
- π Do not ignore the passengerβs mounts.
Sometimes the screws can be tightened quite strongly, so when unscrewing, you need to apply a moderate effort to avoid tearing the slimes. Use a quality screwdriver that sits tightly in the screw head.
If you find screws under decorative plugs, carefully tuck them with a plastic spatula. Metal tools can leave deep scratches on the plastic, which will be noticeable when reassembled.
Pay special attention to the screws located in the hinges area. They are often hidden and require careful access through the narrow space between the box and the dashboard.
- Daily
- Several times a week
- Rarely
- Almost never
Dismantling process and detaching latches
After all visible screws are unscrewed, you can proceed to the direct extraction of the box. At this stage, it is important to act slowly and carefully listen to the characteristic clicks of the fixers.
Start by gently pulling the bottom of the glove compartment over yourself. At this point, the lower anchorages should be snapped. Donβt put too much effort if the box doesnβt lend itself β you may have missed some kind of screw.
Next, you need to take the lower part of the box to the side to free the upper guides. The design provides for the possibility of removing the box through a deviation down and to the side.
- π Smoothly pull the bottom of the box on yourself
- π Take the lower part towards the passenger
- π Pull the top out of the grooves
Connected lamp backlight, which can break when a sharp movement.
If you feel resistance, stop and check if the backlight wire is caught. Carefully disconnect the connector by pressing the lock, and only after that completely remove the box.
βοΈ Check before removal
Working with the opening mechanism and hinges
The mechanism for opening the glove compartment Skoda Yeti It is a system of levers and springs that provide a smooth closing. When dismantled, these elements may present some complexity.
If your goal is not complete removal, but only access to the mechanism, it may be enough to unscrew the hinge fastener from the door of the drawer. This will allow you to throw away the box and access the insides without a complete disassembly.
Often, owners face the problem of sagging the box or opening it spontaneously. Adjusting the spring tension can solve this problem, but requires careful adjustment.
When removing the hinges, pay attention to the condition of the plastic bushings. Over time, they can wear out, which will lead to backlash and creaking during operation.
Removal of the entire mounting assembly may be required to replace the spring or repair the mechanism. In this case, the box is dismantled completely, as described in the previous sections.
What to do if the latch is broken?
If the latch broke, you can temporarily secure the box with tape or plastic screeds. For a full repair, you will need to replace the lock in the assembly, which is sold in dealerships or at disassemblies.
Eliminating squeaks and refinishing the interior
One of the frequent reasons for removing the glove compartment is the fight against unpleasant creaks that occur when driving on uneven roads. Plastic rubbing against plastic creates an annoying sound.
To eliminate the creak, it is necessary to apply a special lubricant or glue felt linings to the contact points of the box with the dashboard. This simple solution can dramatically improve acoustic comfort in the cabin.
It is also recommended to check the condition of shock absorbers (surveyors), if they are installed. Wear of these elements leads to a sharp closure of the box and subsequent vibrations.
- π‘οΈ Apply silicone grease to the guides
- π‘οΈ Stick the felt in the places of contact
- π‘οΈ Check the state of the dampers.
If you plan to install additional lighting, it is better to do it at the stage of removing the box. The wires can be carefully hidden behind a dashboard without disturbing the aesthetics of the cabin.
When assembling, make sure all gaps are uniform and the box opens and closes smoothly. Any distortions can lead to rapid wear of the mechanism.
| element | Material | Condition | Recommendation |
|---|---|---|---|
| Plastic latches | Polypropylene | Wear after 5 years | Replacement with new ones |
| Opening loops | Metal/Plastic | Backlash | Adjustment or lubrication |
| Backlight | LED | Frequent burnout | Replacement with LED |
| Rubber seal | Rubber | Cracks | Replacement or sealing |
Features of access to fuses
On many versions Skoda Yeti The safety lock is located just behind the box. This makes the procedure of removing the glove compartment necessary when replacing the burned fuses.
After dismantling the box, you will see a plastic block cover that is attached to the latches. Carefully tuck it in and remove it to access the fuses.
Each safety lock is signed on the back of the lid or in the instructions for the car. It is important to find the one responsible for the particular faulty system.
The replacement of the fuse should be made only by a current of the same strength. Using a more powerful fuse can cause the wiring to fire.
After replacing the faulty element, be sure to check the operation of the corresponding system before installing the glove compartment in place.
Before removing the glove compartment, take a picture of the location of the wires and connectors so that during the assembly they are not confused with places.
Reassembly rules and final inspection
Installing the glove compartment in place is a process that requires the same care as removing it. The first thing you need to connect the light connector and make sure that it is securely fastened.
Then carefully insert the top of the box into the guides, and then press the bottom part until the characteristic click of the locks.
Donβt forget to wrap all the screws that were removed earlier. Tighten them with moderate effort, so as not to break the thread in the plastic inserts of the dashboard.
Do the final check: open and close the box several times, make sure it does not squeak or squeak. Check the backlight.
If everything is in order, the job can be considered done. A properly installed glove compartment will last for many years without complaints.
The main reason for the problems when removing the glove compartment is an attempt to speed up the process and skip the stage of searching for hidden screws.
β οΈ Attention! When the glove compartment is removed Skoda Yeti With climate control, be extremely careful with ducts passing in the immediate vicinity of the box.
β οΈ Attention! Use only plastic blades to snap the locks. Metal tools can irreversibly damage the paint coating of the dashboard.
Frequently asked questions (FAQ)
Do I need to disconnect the battery before removing the glove box?
It is recommended to turn off the battery only if you plan to work with the backlight wiring or the fuse block. For a simple removal of the box is not necessary, but a precautionary measure will not hurt.
How long does the withdrawal procedure take?
With the experience and the right tools, the process takes about 15-20 minutes. For the first time, without familiarity with the design, it may take 30-40 minutes.
Can I remove the glove compartment without tools?
No, to unscrew the screws of the mounting will necessarily need a cross screwdriver. Without it, the box cannot be completely dismantled.
What to do if the plastic latch breaks?
A broken latch can be temporarily replaced with plastic screeds or tape, but for full repair it is better to replace the entire mechanism or find a suitable part at the disassembly.
Why does the glove compartment creak after installation?
Most likely, you did not tighten the screws properly or did not use lubricant where the plastic contacts. It is recommended to additionally treat the joints with silicone or felt.