Removing the front bumper ŠKODA Octavia Tour (2021–2026): instructions with photos and secrets of the masters

Removing the front bumper ŠKODA Octavia Tour fourth generation (FL, 2021–2026) is a task that owners face when replacing headlights, repairing after an accident, or installing additional equipment. The bumper design here is more complex than that of previous generations: new radar mounts have been added Travel Assist, parking sensors and cameras Area View. Without knowing the nuances, you can break the clamps or damage the wiring.

In this article - step-by-step withdrawal algorithm taking into account the features of the restyled Octavia Tour, including hidden fastenings, electrical work, and tips for avoiding common mistakes. The material is based on the experience of service technicians and analysis of technical documentation ŠKODA (section 57-50-01 for body work). If you have a model before 2021 - pay attention to the differences in the attachment of the side parts of the bumper to the fender liners.

Preparation: Tools and Safety Precautions

Before starting work, make sure you have everything you need. For Octavia Tour with the system Travel Assist (radar in array) additional tools will be required to disable the electronics.

• 🔧 Tools: 10 and 13 mm sockets, T25 and T30 screwdriver, plastic spatulas for clips, wrench for wheel bolts (if removing fender liners).
• 🔋 Electrical: multimeter (for checking sensor circuits), electrical tape, marker for marking connectors.
• 🚗 Additionally: jack, wheel chocks, gloves (the bumper may have sharp edges after an accident).

Important: if on your Octavia Tour installed adaptive cruise control, before removing the bumper necessarily disconnect the negative terminal of the battery for 10–15 minutes. This will reset the errors in the block J428 (Control Unit for Front Sensors), otherwise it may catch fire after assembly ESP on the dashboard.

⚠️ Attention: On models with Matrix LED The headlights are attached to the bumper through additional bolts under the hood. If you do not unscrew them in advance, when removing the bumper, you can damage the LED modules (repair cost - from 40,000 rubles).

Step 1: Removing the front wheel and fender liner

On Octavia Tour 2021+ bumper is attached to the fender liners via hidden clips. To get to them, you will have to remove the wheel and part of the fender liner.

1. Jack up the car and remove the wheel (use a 17mm wheelbrace).
2. Unscrew the 3 T25 screws along the edge of the fender liner and the 2 clips at the bottom (use a plastic spatula to avoid breaking).
3. Bend the fender liner back - you will see 2 10mm bolts securing the bumper to the fender.

On models with wide tires (for example, 225/40 R18) it may be necessary to turn the steering wheel to its extreme position to access the mounts. If the bumper is already damaged, be careful: the plastic may crack when bent.

Battery terminal disconnected (for models with radar)|

The wheel has been removed and put aside|

Safety stops are installed under the jack|

Clip tool at hand-->

Step 2: Disconnecting Electrical Connectors

On Octavia Tour with Travel Assist or Area View Up to 4 connectors are hidden under the bumper:

• 📡 Adaptive cruise control radar (connector T10h, black).
• 📷 360° cameras (2 connectors T8c, gray, under the apron).
• 🅿️ Parking sensors (connector T2,5e, white, on each sensor).

To avoid mixing up the connectors during reassembly, take a photo of their location or mark it with a marker. On models with heated bumper (optional 9U1) there is an additional harness for the heating elements - it cannot be pulled by the wires!

Connector	Color	Purpose	Features
T10h	Black	Radar Travel Assist	It is attached with a latch, pull the body!
T8c	Gray	Cameras Area View	Sensitive to moisture - check the seals
T2,5e	White	Parking sensors	If the sensor is damaged, error PLA 3.0

⚠️ Attention: If after removing the bumper an error light appears on the dashboard ACC faulty, check the integrity of the shielding braid on the radar connector. On Octavia Tour 2023, it often rubs against the edge of the bumper.

Step 3: Unscrewing the main bumper fasteners

Bumper Octavia Tour mounted on 12 points:

• 🔩 4 10mm bolts (2 on each side under the wings).
• 🔩 2 bolts 13 mm (bottom, under the apron).
• 🔗 6 plastic clips (3 on top under the hood, 3 on the bottom).

Start unscrewing with upper mounts under the hood (they are less accessible). Bolts under the apron often stick - use penetrating lubricant WD-40 10 minutes before work. Pull out the clips carefully: in the cold the plastic becomes brittle.

On models with Matrix LED Before removing the bumper, you need to unscrew 2 additional bolts securing the headlights to the bumper (under the hood, next to the radiator). If this is not done, when removing the bumper you can tear off the optics mount.

Step 4: Removing the bumper from the body

When all the fasteners are unscrewed, the bumper is held in place only by the latches on the sides. For removal you will need an assistant or special ties:

1. Gently pull the bumper towards you, starting from right edge (there are fewer wires).
2. Hold the radiator grille - it may fall out along with the bumper.
3. If the bumper is “bitten”, check whether you forgot the clip under the headlight (a typical mistake).

On Octavia Tour with Area View The cameras are attached to the bumper through rubber dampers. When removing, do not pull on the camera wires - they may come off the board (repairs will cost 15,000 rubles per camera).

What to do if the bumper cannot be removed?

If the bumper is stuck, check:

1. Clips under the headlights (often forgotten).

2. Bolts for fastening to the subframe (on models with DCC).

3. Latches near the foglights (may become deformed in an accident).

If all else fails, try lightly pressing the bumper from top to bottom - sometimes this will release the latches.

Step 5: Disassemble the bumper (if necessary)

If you need to replace radiator grille, fog lights or parking sensors, the bumper will have to be disassembled. On Octavia Tour it consists of 3 parts:

• 🔲 Main panel (with fastenings to the body).
• 🔳 Decorative grille (attached with 4 latches).
• 🔴 Bottom apron (on 6 T25 screws).

To remove the grille, press the latches on top and pull it towards you. Be careful: on models with Travel Assist Behind the grille there is a radar, which is mounted on 2 T30 bolts. If you do not unscrew it in advance, you may damage the mount.

The fog lights are mounted with 3 T25 bolts on the back of the bumper. Before removing them, disconnect the connector (white, T3e). On Octavia Tour 2026 foglights use LED modules - do not touch them with bare hands (grease marks will shorten their service life).

Reassembly: nuances and verification

When installing the bumper, pay attention to:

• 🔌 Correct connection of connectors (especially radar - an error will lead to failure ACC).
• 🔧 Tightening the bolts (tightening torque: 10 Nm for fastenings to the body, 8 Nm for headlights).
• 📏 The gaps between the bumper and the fenders (must be the same on both sides).

After assembly, be sure to:

1. Connect the battery and check the operation of all systems (Travel Assist, Area View, foglights).
2. Reset errors via VCDS or ODB2 scanner (codes U111300 and B10CD13 reset automatically after restart).
3. Check the tightness of the fasteners - when washing under pressure, water should not penetrate behind the bumper.

⚠️ Attention: On Octavia Tour with Matrix LED after removing the bumper it may be necessary headlight calibration. If the light beam has moved to the side, contact the service center with the equipment Hella Gutmann or Bosch KTS.

FAQ: Frequently asked questions about bumper removal

Is it possible to remove the bumper Octavia Tour without removing the wheels?

Technically yes, but it will make accessing the side mounts much more difficult. Without removing the wheel and fender liner, you will not be able to unscrew the 10 mm bolts under the arch, and you also risk breaking the clips when applying force to the bumper. On models with wide tires (e.g. 235/35 R19), wheel removal is mandatory.

What to do if the bumper lights up after removing it? Check Engine?

Most likely the problem is in the radar connector Travel Assist. Check:

1. Integrity of the shielding braid on the connector T10h.
2. Presence of oxidation on the contacts (clean with alcohol).
3. Correct connection (pins must match according to the diagram).

If the error remains, reset it using the diagnostic scanner. Code P0504 (brake system malfunction) often appears after the radar is turned off.

How to remove the bumper if it is damaged after an accident and the clips are broken?

In this case:

• Use a flat-blade screwdriver to carefully pry out the remaining parts of the clips.
• If the bumper is deformed, try heating the plastic with a hair dryer (temperature no higher than 60°C) to restore its flexibility.
• To attach the new bumper, use repair clips (article 1U0 807 231 A for Octavia).

Do not try to pull out the bumper by force - this may damage the fastenings on the body (for example, brackets under the headlights).

Do I need to remove the bumper to replace fog lamps?

No, on Octavia Tour 2021+ fog lamps (H11 or LED) can be changed without removing the bumper. Enough:

1. Unscrew 2 T25 screws under the bumper (right and left).
2. Disconnect the power connector.
3. Turn the socket counterclockwise and remove the lamp.

The exception is models with Matrix LED, where fog lights are integrated into the headlights. In this case, the bumper will have to be removed.

What clips should I buy for replacement?

For ŠKODA Octavia Tour (2021–2026) the following articles are suitable:

Clip type	Article	Quantity per bumper
Upper (under the hood)	1U0 807 231 A	3 pcs.
Lateral (to the wing)	1U0 807 143	4 pcs.
Bottom (under the apron)	1U0 807 215	2 pcs.

When purchasing, take spare clips - they often break during dismantling. Original clips ŠKODA stronger than analogues, but more expensive (from 150 rubles per piece).