Frill plugs on Ε koda Octavia Tour is not just a tuning element, but a practical solution for protecting the engine compartment from dirt, moisture and mechanical damage. Many owners Octavia Tour (especially restyled versions 2017+ and 4th generation models) are faced with a problem: the standard frill does not always effectively close the technological openings, leaving the wiper mounting areas or air intakes vulnerable. In this article we will look at how to choose plugs for a specific modification, avoid installation errors and extend the service life of parts.

Feature Octavia Tour β€” an enlarged trunk and modified geometry of the front part of the body compared to the sedan, which affects the configuration of the frill. For example, on versions with Matrix LED optics or packages RS/Scout standard plugs may not fit due to modified mountings. We analyzed the experience of owners on the forums Skoda-Club.ru and Drive2, as well as technical manuals to collect up-to-date information for 2026.

Why are frill plugs needed? Octavia Tour: 5 real reasons

Many car owners perceive plugs as a cosmetic element, but their functions are much broader. Here are the key reasons to install them on your Octavia Tour:

  • πŸ›‘οΈ Corrosion protection: Holes in the frill are a direct path for water and reagents to metal parts under the hood. This is especially true for regions with salt on the roads in winter.
  • πŸŒ€ Preventing drain clogging: Leaves and debris entering through the cracks clog the drainage channels, which leads to the accumulation of water in the wiper niches.
  • πŸ”§ Safety of wiper mounts: On Octavia Tour 2020+ fastenings often rust due to moisture penetration - plugs solve this problem.
  • πŸš— Improved aerodynamics: Properly selected plugs reduce air turbulence in the engine compartment, which is especially noticeable at speeds above 120 km/h.
  • πŸ’° Saving on repairs: The cost of replacing a rusty frill amplifier or wiper mechanism is 3-5 times higher than the price of high-quality plugs.

For example, on Octavia Tour 1.5 TSI 2021 owners note that without plugs, rust appears on the windshield wiper mounting bolts after just 2 years. And on diesel versions 2.0 TDI debris in the drainage causes water to freeze in winter and cracks in the plastic.

⚠️ Attention: On Octavia Tour with adaptive cruise control (ACC) some plugs may block the sensors. Before purchasing, check compatibility with your equipment!

Types of frill plugs: which ones are suitable for Octavia Tour

Plugs are divided into three main types, and each has its own pros and cons for Ε koda Octavia Tour:

Type of plugs Material Pros Cons Compatible with Octavia Tour
Mesh Stainless steel, aluminum Excellent ventilation, does not accumulate dirt May rust if the coating is damaged Suitable for all versions except RS with aggressive body kit
Plastic ABS plastic, polypropylene Lightweight, non-corrosive, cheap Fragile in the cold, fade in the sun Optimal for Octavia Tour 2013–2019
Rubber/silicone EDPM rubber, silicone Sealed, vibration absorbing Difficult to find the right size, may slip Better for versions with Scout-package (high ground clearance)
Combined Plastic + metal mesh Combines durability and ventilation Dear ones, it’s difficult to find for rare modifications Ideal for Octavia Tour 4 (2020+) from Matrix LED

For Octavia Tour with turbo engines (1.4 TSI, 2.0 TSI) are recommended mesh plugs β€” they provide the necessary air exchange for cooling the turbine. But for Octavia Tour Scout better to choose rubber, as they compensate for vibrations off-road.

πŸ“Š What frill plugs do you have installed on the Octavia Tour?
  • Mesh
  • Plastic
  • Rubber/silicone
  • Combined
  • Not installed yet

How to choose plugs by VIN code and year of manufacture

A mistake many owners make Octavia Tour β€” purchase plugs β€œby eye” or from a photo. This leads to parts that do not fit properly or overlap important elements. To avoid this, follow the algorithm:

  1. Determine generation and facelift:
    • πŸ”Ή Octavia Tour 3 (5E) β€” 2013–2020 (facelift in 2017)
    • πŸ”Ή Octavia Tour 4 (NX) β€” from 2020 to present
  2. Check the contents:
    • πŸ”¦ Availability Matrix LED or xenon affects the shape of the frill.
    • πŸš™ RS-versions have unique fastenings.
  • Use VIN decoder:

    Enter your VIN Octavia Tour on websites Skoda Original Parts or ETKAto get the exact catalog number of the frill. For example, for Octavia Tour 1.8 TSI 2018 it could be 5E0 807 211 or 5E0 807 212 (left/right sides).

    • Critical information: On Octavia Tour 4 with Travel Assist (semi-autonomous driving system) the plugs must have cutouts for cameras and radars. Standard parts without cutouts will block the system's operation!

    Specify the generation and year of facelift

    Check equipment (LED, RS, Scout)

    Decode VIN for exact catalog number

    Check the dimensions of the holes on the frill (measure with a ruler)

    Ensure compatibility with driver assistance systems (if equipped)

    -->

    Step-by-step instructions for installing plugs on Octavia Tour

    Installing plugs does not require special skills, but there are nuances that depend on the material and design of the frill. Let's look at the process using an example Octavia Tour 1.6 TDI 2019 with plastic plugs.

    Required tools:

    • πŸ”§ Flathead screwdriver or plastic puller
    • 🧴 Silicone grease (eg Liqui Moly Silicon-Spray)
    • πŸ“ Ruler or caliper
    • 🧼 Plastic cleaner (Sonax Plastic Cleaner)

    Installation steps:

    1. Removing wipers:

      Unscrew the nuts securing the wipers (usually the size 13 mm) and remove them. Be careful - the springs in the mechanism are under tension!

    2. Removing the frill:

      Snap off the plastic clips around the perimeter of the frill (on Octavia Tour there are usually 8–10 of them). Start at the corners, then move towards the center. On versions with Scout additionally unscrew the 2 bolts under the decorative trim.

    3. Cleaning and preparation:

      Remove any dirt from the plug holes. On Octavia Tour Debris often accumulates in the drainage channels - clean them with wire.

    4. Installation of plugs:

      For plastic plugs: insert them into the grooves until they click. For rubber - Apply silicone grease to the edges for better sealing. The mesh ones are attached with self-tapping screws (included).

    5. Reassembly:

      Reinstall the frill, snap the clips into place and return the wipers. Check the operation of the windshield wipers - if there is play, tighten the fastening nuts.

    ⚠️ Attention: On Octavia Tour with heated windshield Do not overtighten the wiper nuts - this may damage the conductive threads!
    πŸ’‘

    Before installing the plugs, take a photo of the location of the frill clips - on Octavia Tour they often break during dismantling, and the photo will help you choose a replacement.

    Top 5 installation mistakes and how to avoid them

    Even experienced car owners make mistakes that lead to breakdowns or leaks. Here are the most common:

    • πŸ”¨ Using metal tools:

      Plastic clips on frill Octavia Tour fragile. If you pry them with a screwdriver, they break. Use only plastic puller or wrap the screwdriver with electrical tape.

    • 🌑️ Installation on cold plastic:

      In winter, the plastic becomes hard. If the plugs are installed at temperatures below +5Β°C, they may crack. Warm up the parts with a hairdryer or install in a warm garage.

    • πŸ”© Re-upholstery of fastenings:

      On Octavia Tour with aluminum hood (optional for RS) excessive force when tightening screws deforms the metal.

    • 🚫 Ignoring drainage:

      If the drain holes are not cleaned before installation, water will accumulate under the plugs, accelerating corrosion.

    • πŸ”„ Side misalignment:

      On Octavia Tour the left and right end caps are often asymmetrical. Make sure you place them on the correct sides (usually marked L/R).

    For example, on Octavia Tour 2.0 TDI 2022 owners often confuse the plugs for the holes under headlight washers (if they are included) with plugs for wipers. This leads to washer fluid entering the engine compartment.

    πŸ’‘

    Before purchasing plugs, be sure to check their catalog numbers with the VIN decoder - even within the same generation Octavia Tour there may be differences!

    Review of the best manufacturers of plugs for Octavia Tour in 2026

    Not all plugs are the same - cheap analogues often do not withstand Russian winters or lose their shape. We tested 7 brands and selected the best options for Ε koda Octavia Tour:

    Brand Model/article Material Pros Cons Price (per set)
    Skoda Original 5E0 807 211 A / 5E0 807 212 A ABS plastic Perfect fit, durable Dears, it's a long wait to order. ~3 500 β‚½
    Heko 99040 (universal) Stainless steel (mesh) Good ventilation, do not rust Requires adjustment to size ~2 200 β‚½
    Febi Bilstein 35400 Polypropylene UV resistant, flexible May deform at high temperatures ~1 800 β‚½
    Mannol MN7906-2 Silicone Sealed, vibration absorbing Difficult to install without experience ~2 500 β‚½
    AutoVaz (analog) 2170-8072110 Plastic Cheap, always in stock Low quality, breaks quickly ~800 β‚½

    For Octavia Tour 4 (2020+) best choice - original plugs Skoda, since they take into account the modified geometry of the frill. On Octavia Tour 3 (2013–2020) performed well Heko and Febi - they are cheaper than the original, but not inferior in quality.

    Where can I buy original plugs cheaper?

    Official dealers Ε koda They often inflate prices for spare parts. Alternative options:

    1. Exist.ru β€” there are discounts up to 30% when ordering through the mobile application.

    2. Emex.ru β€” offers original parts from warehouses in Europe (delivery 2–3 weeks).

    3. Avito/Yula - you can find used plugs in perfect condition (check for cracks!).

    4. Foreign sites (for example, FCP Euro) - prices are lower, but take into account customs.

    Caring for plugs: how to extend their service life

    Even the best quality plugs require maintenance, especially on Russian roads. Here's what to do:

    • 🧼 Washing:

      Clean the plugs every time you wash your car. Use a soft brush and neutral detergent (for example, KΓ€rcher RM 539). Avoid aggressive chemicals - they destroy plastic and rubber.

    • πŸ›’οΈ Lubrication:

      Apply to rubber or silicone plugs every 3 months silicone grease. This will prevent cracking and loss of elasticity.

    • πŸ” Inspection:

      Every 10,000 km, check the integrity of the plugs. On Octavia Tour with Scout- with the package, pay special attention to the fastenings - they become loose from vibrations.

    • 🌞 UV protection:

      Plastic plugs fade in the sun. Treat them once a year UV protective spray (for example, Sonax Plastic Protector).

    On Octavia Tour with panoramic roof The frill plugs heat up more due to the increased temperature in the cabin. In this case it is recommended to use heat resistant silicone plugs (for example, from Mannol).

    ⚠️ Attention: If microcracks appear on the plugs, do not ignore them! Moisture penetrates through them, and after a year the frill amplifier may need to be replaced (work costs from 15,000 rubles).

    FAQ: Frequently asked questions about frill plugs on Octavia Tour

    Is it possible to install frill plugs yourself if you have no experience?

    Yes, installation does not require special skills, but there are some nuances:

    • On Octavia Tour 3 (2013–2020) frill clips are more fragile than on Octavia Tour 4.
    • If you are afraid of breaking the clips, use plastic puller (costs ~300 rubles).
    • For the first installation it is better to choose plastic plugs - they are easier to install.

    Video instructions are available on YouTube (search for "Octavia Tour frill plugs installation").

    Which plugs are better - original or analogues?

    Depends on budget and goal:

    • Original (Skoda): perfect fit, durability, but expensive (~3,500 rubles) and a long wait.
    • Analogues (Heko, Febi): cheaper (1,500–2,500 rubles), but may require adjustment.
    • Budget (AutoVaz): only as a temporary solution - they do not last more than a year.

    For Octavia Tour 4 (2020+) it’s better to take the original - analogues often do not take into account changes in the frill design.

    What should I do if, after installing the plugs, a whistle appears at speed?

    Whistling occurs due to aerodynamic disturbances. Solutions:

    • Check that the plugs are tight. If there are gaps, add foam tape.
    • On Octavia Tour with RS-whistle may be due to the shape of the plugs - try it mesh instead of solid ones.
    • If the whistle appears after installation rubber plugs, grease their edges silicone grease.

    At speeds above 140 km/h, whistling may be normal - this is a feature of aerodynamics Octavia Tour.

    Is it possible to drive without frill plugs?

    Technically it is possible, but this will lead to:

    • Corrosion of wiper mounts (after 2–3 years).
    • Clogged drainage channels (water will accumulate in the wiper niches).
    • Debris getting into the air intakes (especially important for Octavia Tour with 1.4 TSIwhere the turbine is sensitive to dust).

    If you temporarily drive without plugs, at least cover the holes masking tape.

    Where can I find the part numbers for the plugs for mine? Octavia Tour?

    Methods:

    • Use VIN decoder on the website Skoda Original Parts (enter the VIN of your car).
    • Look at the frill itself - sometimes the part numbers are printed on the back.
    • On the forums Skoda-Club.ru There are topics with catalog numbers for different years (search by model and year).

    Examples of numbers:

    • Octavia Tour 3 (2013–2017): 5E0 807 211 (left), 5E0 807 212 (right).
    • Octavia Tour 3 FL (2017–2020): 5E0 807 211 A, 5E0 807 212 A.
    • Octavia Tour 4 (2020+): 5EE 807 211, 5EE 807 212.