Keychain ล koda Kodiaq is not just a car key, but a complex electronic device with remote control, immobilizer and sometimes even backlight. When the battery in it runs low, you begin to notice the first signs: the signal only works at close range, the buttons respond every once in a while, and a warning appears on the dashboard about a weak key signal. If you ignore these symptoms, one day the key fob will stop opening the car at all - and you will have to use a mechanical key or contact a service for reprogramming.
Replace the battery in the key fob Kodiaq you can do it yourself in 10โ15 minutes, without the help of a dealer. The main thing is to know exact battery type (it depends on the year of manufacture and configuration), have suitable tools on hand and follow the instructions so as not to damage the case or electronic board. In this article we will analyze the replacement process step by step, talk about the nuances for different versions of key fobs (including backlit keys and keyless entry Keyless), and also give tips on how to extend the life of a new battery.
Which battery to buy for the ล koda Kodiaq key fob
The type of battery depends on the generation of the car and the type of key fob. In most cases for Kodiaq (2017โ2026) in use lithium batteries type CR2032 (3 V, 220 mAh), but there are exceptions:
- ๐ CR2032 โ standard for key fobs without illumination (article number of the original battery from ล koda:
N 910 891 01). - ๐ CR2026 โ found in keys with backlit buttons (thickness 2.5 mm versus 3.2 mm for CR2032).
- ๐ CR1632 - rare, but installed in key fobs with the function Keyless (keyless entry).
To accurately determine the type, remove the old battery and look at the markings on its case. If the key fob is being disassembled for the first time, refer to the table below. Buy batteries trusted brands: Duracell, Energizer, Panasonic or Varta. Cheap analogues can leak and damage the electronic board.
| Year of issue Kodiaq | Keychain type | Recommended battery | Notes |
|---|---|---|---|
| 2017โ2020 | Standard (no backlight) | CR2032 | Original article: N 910 891 01 |
| 2021โ2026 | With backlit buttons | CR2026 | Thickness 2.5mm, check before purchasing! |
| 2022โ2026 | Keyless | CR2032 or CR1632 | Depends on the key fob firmware version |
โ ๏ธ Attention: Do not use batteries that have expired (indicated on the packaging)! Even if they are new, the chemical processes inside could be disrupted, which will lead to electrolyte leakage and corrosion of the key fob contacts.
Battery replacement tools
To disassemble the key fob ล koda Kodiaq You donโt need professional toolsโwhatโs found in every home is enough. Main rule: don't use forceso as not to break the housing latches. Here's what you'll need:
- ๐ง Flat head screwdriver (or mediator) - to separate the halves of the body.
- ๐ฑ Smartphone with flashlight โ to illuminate the insides of the key fob when replacing.
- ๐งฒ Magnet or tweezers - will help you remove the old battery if it is stuck.
- ๐งด Alcohol wipes โ to clean contacts from oxidation (if the battery has leaked).
If the key fob is equipped with the function Keyless, prepare additionally plastic spatula (for example, for removing smartphone screens) - it will help you carefully pry off the case without damaging the keyless entry antenna.
- Screwdriver
- Mediator
- Knife
- Plastic spatula
- Other
Step-by-step instructions: how to disassemble the key fob
Keychain body Kodiaq consists of two halves fastened with latches. The main mistake beginners make is trying to separate them with a knife or screwdriver in the middle. This leads to chipping of the plastic and damage to the buttons. Proceed carefully:
Place the keychain on a flat surface buttons down. The mechanical key (if built-in) must be removed.
Insert a flathead screwdriver or pick into gap between body halves on the side where there are no buttons (usually a clip is located there).
Gently twist the tool to release the latches. It will start from the mechanical key side.
When the housing opens slightly, do the same on the opposite side. Don't delay force the halves - they should separate easily.
If the key fob does not budge, check to see if there is a mechanical key left inside - it may block disassembly. In backlit keys, you will first have to remove the LED module (it is attached to two small latches).
โ๏ธ What to check before disassembling the key fob
โ ๏ธ Attention: In keychains Kodiaq 2023โ2026 with feature Keyless There is a miniature antenna inside the case. If it is damaged, keyless entry will stop working, and repairs will cost 5โ10 thousand rubles.
Replacing the battery: nuances for different types of key fobs
When the case is disassembled, you will see a circuit board with a chip and a battery socket. In most cases, the battery is held on a plastic clip or metal retainer. Remove the old battery by prying it off with a screwdriver or magnet, and install a new one, observing polarity (plus should look up).
Features for different versions of key fobs:
- ๐ Standard key fob (without backlight): battery
CR2032Installs into the socket without additional fasteners. After replacement, check if the contacts are bent. - ๐ก With backlit buttons: before replacing the battery
CR2026disconnect the LED module (it is attached to two wires). Do not pull on the wires - they are fragile! - ๐ถ Keyless (keyless access): the battery can be soldered to the board. In this case, you will need a soldering iron or contact service.
In keychains ล koda Kodiaq Models 2020-2021 may need to reset the remote control after replacing the battery. To do this, press and hold the buttons LOCK and UNLOCK simultaneously for 10 seconds until the LED flashes 3 times.
What should I do if the key fob does not work after replacement?
If the key fob does not respond to button presses, check:
1. Correct installation of the battery (polarity!).
2. The integrity of the contacts on the board (are they bent?).
3. Presence of oxidation - clean contacts with alcohol.
If the problem persists, the immobilizer settings may have gone wrong. In this case, reprogramming will be required at the dealership (cost ~1,500โ3,000 rubles).
Assembling the key fob and checking its functionality
When the battery is installed, all that remains is to assemble the key fob in reverse order. Make sure that:
- ๐ All body latches tightly fixed (no play).
- ๐ Battery contacts not closed foreign objects (for example, pieces of plastic).
- ๐ Mechanical key easy to insert and remove.
To check functionality:
- Move 5โ10 meters away from the car.
- Click the button
UNLOCKโ the alarm should work the first time. - Check the operation of the backlight (if any) and keyless entry Keyless.
If the key fob is unstable (for example, it only opens the car at close range), the reason may be dead car battery or synchronization failure. In this case, follow the reprogramming procedure:
1. Insert the key into the ignition.2. Turn to "ON" position (do not start the engine).
3. Press the "LOCK" button on the key fob 3 times in a row.
4. Turn off the ignition and repeat steps 1โ3 2 more times.
After replacing the battery in the key fob Keyless The keyless entry system may need to be rebooted. To do this, remove and reinsert the battery in the car (under the hood or in the trunk), then wait 1-2 minutes.
Common mistakes and how to avoid them
Even with the apparent simplicity of the process, many owners Kodiaq make mistakes that lead to breakage of the key fob. Here are the most common of them:
| Error | Consequences | How to avoid |
|---|---|---|
| Using a knife to disassemble | Scratches on the case, broken latches | Use a plastic spatula or pick |
| Installing the battery with the wrong polarity | Short circuit, board failure | Plus (+) must look up |
| Application of force during assembly | Case cracks, antenna damage Keyless | The latches should fit without effort |
Another typical problem is ingress of dirt or moisture inside the keychain. If you notice corrosion on the contacts, clean them with alcohol and dry the key fob with a hair dryer (at minimum temperature) for 10-15 minutes. Never use acetone or solvents for cleaning - they destroy plastic and rubber seals!
If after replacing the battery, the key fob stopped working, do not try to disassemble it again. It is likely that the problem is in synchronization failure with the car, and not in mechanical failure. Contact the service for the diagnosis of the immobilizer.
How to extend the life of the battery in your key fob
Average battery life in a key fob ล koda Kodiaq 2-3 years, but with proper operation, this period can be extended to 4-5 years. Here are some tips:
- ๐ Do not store the keychain near metal objects (keys, coins) -- this creates parasitic currents that drain the battery.
- ๐ก๏ธ Avoid extreme temperaturesDo not leave the key fob in direct sunlight (for example, on a dashboard in summer) or in the freezer.
- ๐ Turn off the button backlightIf you do not use it (in some key fobs it is activated by double pressing any button).
- ๐ฑ Do not carry a keychain in the same pocket with a smartphone NFC chips can interfere with the signal.
If you rarely use a car (for example, in winter), remove the battery from the keychain and store it separately. It'll prevent self-discharge. Before long parking (more than 2 weeks) it is also recommended to turn off the function. Keyless through the car menu (Settings โ Center. locking-in).
FAQ: answers to frequently asked questions
Can I use a watch battery instead of a CR2032?
No. Watch batteries (eg LR44 or SR44) have a different voltage (1.5 V instead of 3 V) and size. Their installation will lead to incorrect operation of the keychain or its breakage.
Why does the key fob only work near the car, even though the battery is new?
The reason may be discharged (voltage below 11.8 V), synchronization failure or failure of the immobilizer antenna. Try reprogramming the key fob (instruction above) or checking the battery voltage.
What should I do if, after replacing the battery, the key fob does not sync with the car?
Perform the retraining procedure:
- Close all doors.
- Put the key in the ignition lock and turn to the "ON" position.
- Press and hold the button
LOCKon the key fob for 5 seconds. - Repeat step 3 2 more times.
If it doesnโt help, contact the service to diagnose the immobilizer.
Is it possible to charge a CR2032 battery if it is dead?
No, CR2032 It is a lithium battery that is not designed to be recharged. Attempts to charge it can lead to swelling, leakage of the electrolyte and damage to the keychain.
Where to buy the original battery for the keychain Kodiaq?
The original battery ล koda (article N 910 891 01) is sold in dealerships (price ~300-500 rubles). Analogues (Duracell, Energizer) can be purchased in electronics stores or ordered Wildberries/Ozon.