Crossover owners Skoda Kodiaq 2020 model years often encounter the need to reset the service indicator after scheduled maintenance. The car’s on-board electronics, configured to record mileage and time, continue to require a service visit, even if the oil and filters have already been changed. Ignoring this function does not affect the performance of the engine, but creates visual discomfort and may raise questions during the subsequent sale of the car.
The procedure for resetting the interval on the 2020 model has its own characteristics, depending on the configuration of the multimedia system and the version of the dashboard firmware. In some cases, the standard menu may be hidden or have modified operating logic, which requires the use of specific button combinations or external diagnostic equipment. Understanding the algorithm of actions will allow you to avoid mistakes and correctly set up a reminder for the new period of operation.
Preparing for the service interval reset procedure
Before you begin any manipulations with the on-board computer, you must make sure that all routine maintenance work Skoda Kodiaq completed. Changing the engine oil, air and cabin filters must be carried out before the reset, since the system records the condition of the car at this very moment. If you reset the interval ahead of time, the wear sensors and mileage will not be correctly synchronized with the actual state of the units.
An important step is preparing the car itself. Start the engine and let it idle for a few minutes to allow the system to fully initialize all electronic control units. Make sure the battery is in good condition and has sufficient charge as the reset process may take time and low voltage may cause malfunction BCM (body control unit). Turn off all additional energy consumers such as air conditioning, heated seats and the audio system.
It is also worth checking the current settings for displaying information on the dashboard. If you have a digital instrument panel installed Active View or Virtual Cockpit, the interface may differ from classic analog devices. Make sure you see the current mileage and remaining life until the next maintenance. This will help you control the process and notice in time if the system does not accept the reset command.
Reset via on-board computer and dashboard menu
The most common method for resetting the interval to Skoda Kodiaq 2020 does not require complex diagnostic equipment and is carried out through standard buttons on the steering wheel or instrument panel. First, you need to switch the car to ignition mode without starting the engine, or start it and turn it off, leaving the ignition on. This is necessary to activate the electronics without placing a load on the starter and engine.
Go to the settings menu using the steering wheel controls. Find the section responsible for car settings or service functions. Depending on the software version, the path may look like Menu → Vehicle settings → Service. Inside this section, you will see an option for “Service Interval” or “Reset Service Interval.” Select this item and confirm the action by holding the "OK" or "Menu" button for a few seconds.
Some firmware versions require holding down the “0.0/SET” button on the instrument panel when turning on the ignition. In this case, a message indicating readiness to reset should appear on the display. Make sure the screen displays confirmation of the successful operation, usually a check mark or a "Reset Complete" message. If the system displays an error, check whether access to service functions is blocked due to an activated warranty or specific dealer settings.
⚠️ Caution: Do not attempt to reset the interval if the display shows an engine error or other critical warnings. Correct the problem first, otherwise the system may block the reset option again.
☑️ Preparing to reset via menu
Using the OBD2 diagnostic adapter
If the standard method through the menu does not work or the interface of the car does not allow access to service functions, you will need to use external diagnostic equipment. Specialized adapters, such as VAG-COM (VCDS) or CaristaThey allow you to interact directly with the control units of the car. This is especially true for 2020 models, where software may have hidden features or require authorization to change settings.
Connect the adapter to the OBD2 connector located under the steering column on the left side. Run the appropriate application on a smartphone or laptop and wait for the installation of communication with the car. In the program menu, select the control unit "Block 17 - Instrument Panel" or "Block 19 - CAN gateway". Find the function of adapting or resetting service intervals. Enter the appropriate code or select the reset option from the drop-down list.
After sending a command to reset, the system may require confirmation. Make sure the process is completed successfully and check the dashboard. The screen should display a new mileage value to the next scheduled maintenance. If you use professional equipment, you can also check if there are any errors in the memory of the control units after the procedure. This ensures that the reset is correct and does not disrupt other systems.
What if the adapter does not see the control unit?
If the application cannot connect to a particular block, check the adapter connection, battery charge and software version. You may need to update the adapter drivers or use more specialized software such as ODIS.
It is worth noting that the use of third-party software requires some caution. Incorrect actions can lead to failures in the operation of electronic systems. Therefore, if you are not confident in your abilities, it is better to entrust this procedure to professionals. However, with experience and appropriate equipment, self-resetting saves time and money.
- Through the car menu
- Via diagnostic adapter
- Contacting service
- I don't know how to do this
Resetting the interval for diesel engines with a particulate filter
Owners Skoda Kodiaq Diesel-powered engines (TDIs) have their own service features, especially when it comes to particulate filter (DPF). The interval reset for these cars is often associated not only with oil replacement, but also with the regeneration of the exhaust gas treatment system. If you reset the interval without taking into account the DPF status, the system may continue to issue warnings about the need for forced regeneration.
For diesel models, the discharge procedure may include checking the condition of the filter and its regeneration. In some cases, if the filter is contaminated, the system will not allow the interval to be reset until forced regeneration is carried out through the diagnostic scanner. This is important to prevent the failure of expensive particulate filter. Check the error code if the system issues a DPF alert.
When using diagnostic equipment for diesel versions, pay special attention to the engine control unit and the exhaust control unit. Make sure that all regeneration parameters are normal. Only then can you move on to reset the service interval. This will ensure the correct operation of the system and prevent possible problems in the future.
⚠️ Warning: On the 2020 diesel versions of the Skoda Kodiaq, resetting the interval without checking the condition of the particulate filter can lead to quick clogging and expensive repairs.
Typical errors and ways to resolve them
In the process of resetting the service interval, owners often encounter a number of errors that can be caused by both human factors and technical features of the car. One of the most common mistakes is to attempt a reset without performing all the necessary maintenance procedures. The system can block reset if sensors detect that oil or filters have not been replaced, or if time and mileage intervals do not match the specified parameters.
Another common problem is the incorrect operation of the dashboard menu. In this case, it can help to update the car software or reset the settings to factory. It is also worth checking whether access to service functions is blocked due to an activated warranty or specific dealer settings. If the problem is not solved, it is recommended to contact the official service center.
Sometimes the system can produce an error even if all the actions are done correctly. In this case, try resetting the onboard computer settings by turning off the battery for a few minutes. This will help to reboot all electronic blocks and eliminate temporary failures. After connecting the battery again try to perform the reset procedure.
Before resetting the interval, take a picture of the current settings and messages on the dashboard – this will help you quickly recover them after resetting if something goes wrong.
Table of service intervals for the Skoda Kodiaq 2020
For the convenience of the owners Skoda Kodiaq In 2020, a table with recommended service intervals is presented. This data will help you plan visits to the service and properly configure reminders in the onboard computer. The intervals may vary depending on the type of engine, operating conditions and recommended oil.
| Type of service | Mileage (km) | Time (months) | Note |
|---|---|---|---|
| Changing oil and filters | 15 000 | 12 | At least once a year |
| Replacing the air filter | 30 000 | 24 | Depends on conditions |
| Replacing the fuel filter (diesel) | 60 000 | 48 | Definitely TDI |
| Replacing the timing belt | 210 000 | 120 | Check every 60,000 |
| Replacing brake fluid | 30 000 | 36 | Every 3 years |
Regular adherence to service intervals prolongs the life of the engine and reduces the risk of costly breakdowns, especially on diesel versions with a particulate filter.
Frequently asked questions from Skoda Kodiaq owners
Owners Skoda Kodiaq Often ask questions related to the procedure of resetting the service interval. Below are the answers to the most common ones that will help you understand the nuances of your car’s maintenance.
Can I reset the interval without visiting the service center?
Yes, the reset can be done independently through the menu of the onboard computer or using the OBD2 diagnostic adapter. However, if you have doubts about the correctness of the procedure, it is better to contact specialists.
What happens if you don’t drop the interval after the service?
An untimely reset will not affect the operation of the car, but the dashboard will continue to be lit with a warning about the need for maintenance. This may raise questions when selling a car or during a routine inspection.
Can I reset the interval if the brake fluid has not been replaced?
Technically, this is possible, but not recommended. The system monitors not only the mileage, but also the condition of various liquids. Resetting the interval without replacing the brake fluid can lead to a decrease in the effectiveness of the brake system.
How often should you check the engine oil level?
It is recommended to check the oil level every 1000 km or before each long trip. This will help to avoid problems with the engine and extend its service life.
Can I use normal motor oil instead of the recommended one?
Not recommended. Using oil that does not meet the manufacturer’s specifications can lead to premature engine wear and loss of warranty. Always use the oil recommended in the operating manual.
Compliance with all recommendations and timely service Skoda Kodiaq 2020 will ensure that your car is running reliably and that you have no electronics issues. Remember that the correct reset of service interval is not just a formality, but an important part of keeping the car in excellent condition. If you have any further questions, contact the authorized dealers or use specialized literature.
⚠️ Warning: Incorrect resetting of the service interval can lead to loss of warranty on the car, if it is still in warranty service. Always check the terms with the official dealer.
Proper and timely maintenance of the ŠKODA KODIAQ 2020, including correct interval resetting, ensures the vehicle’s durability and the absence of electronics issues.