Removing the door card on cars of the family Skoda Tour (modification based on Skoda Fabia or Skoda Octavia A5) is a procedure that requires accuracy and understanding of the body structure. Many owners are faced with the need for disassembly when replacing a speaker, installing an alarm system or repairing power windows. Improper impact can lead to broken plastic pistons or deformation of the panel itself, which will subsequently cause extraneous sounds when driving.
Unlike more modern models, in Skoda Tour Combined fastening methods are used: screws under decorative plugs and metal clips. The process requires not only physical strength, but also knowledge of the exact points of application of force. It is important to understand that after removing the card, access to the lock mechanism and wiring will become complete, but the risk of losing small parts also increases.
Preparing tools and workspace
Before you begin, you need to organize a clean place where you will sort the removed parts. The absence of dust and dirt is critical, since the lock and window mechanism is very sensitive to small particles. You will need a set of Phillips and flathead screwdrivers, as well as special plastic cards for removing the trim.
Using metal tools such as screwdrivers or knives to pry the card Skoda Tour Absolutely not recommended without proper protection. You can easily scratch the door's paintwork or leave deep marks on the soft plastic. If you don't have a professional set, use an old bank card or piece of thick plastic to use as a spacer.
- ๐ง A set of flat-head screwdrivers of different widths (for prying off the plugs)
- ๐ช Plastic spatulas or cards for dismantling (protection of plastic)
- ๐ฉ Torx screwdriver (star) T20 or T25 (for lock screws)
- ๐ฆ Container for storing small pistons and screws
โ ๏ธ Attention: Before starting work, be sure to disconnect the negative terminal of the battery. In the system Skoda Tour There are airbags located in the doors, and accidental shorting of the contacts may cause them to unintentionally deploy.
Pay special attention to the condition of the pistons themselves. If the car has significant mileage, the plastic of the clips may become brittle. Be prepared for the fact that some of them may fail and break during dismantling. Have spare fasteners on hand so you don't drive around with a dangling door.
Removing decorative plugs and unscrewing screws
The process begins with searching for hidden fasteners. In models Skoda Tour Manufacturers often hide screws under decorative inserts. First of all, carefully inspect the door handle and armrest. In the recess of the handle there is often a plug that hides the fastening screw.
Carefully pry up the plastic plug with a thin flathead screwdriver. Be careful not to force too hard to avoid breaking the plug itself, as finding a replacement for older models can be difficult. After removing the plug, you will see a Phillips screw that needs to be unscrewed until it stops.
Next, check the armrest. In some door modifications Skoda Tour the screw may be located under the cover of the small items compartment or under the decorative insert at the end of the door. Unscrew any screws you find and put them in a safe place. Never leave screws on the bottom of the door to prevent them from falling behind the trim.
- ๐ Inspect the inside of the door handle
- ๐ Check for a screw in the armrest or pocket
- ๐ Make sure there are no hidden screws on the bottom of the card
โ๏ธ Preparation for dismantling
If you don't see screws in the usual places, it's possible that the card is only held on by clips, but this is rare for Skoda Tour. Carefully examine the entire perimeter zone. Sometimes the manufacturer places fasteners under the decorative trim of the speakers if it is removed separately.
Hidden screw in the mirror
Sometimes the card securing screw may be located at the junction of the door and rear view mirror. If you have a power adjustable one, you may need to remove the triangular mirror trim.
Release the fasteners and remove the card
When all screws are unscrewed, you can proceed to the most important stage - clipping. Take a plastic spatula and insert it into the gap between the door map and the metal door. Start from the bottom, moving around the perimeter. Do not push hard so as not to break the fasteners.
You need to hear the characteristic clicks โ this is a signal that the piston has come out of its seat. Move smoothly: first, snap the bottom, then the sides and lastly the top of the glass. In the upper zone, there are often clips holding the card relatively tightly.
Do not pull the map on yourself sharply and immediately along the entire plane. This can cause you to break the wiring or break the plastic fixtures. First, free one side, then the other, gradually increasing the gap. If the card fails, check if you forgot to unscrew some screw.
- ๐ ๏ธ Put the blade in the lower joint of the door and cards
- ๐ ๏ธ Move around the perimeter, snapping clips in turn
- ๐ ๏ธ Do not pull the card on yourself until you have released all the fixers.
- Special plastic spatula
- Old bank card
- Metal screwdriver (with caution)
- Knife
After all clips are released, the card will be held only on the wires and lock mechanism. Do not put it on the floor and do not leave it hanging on the wires. Carefully lift the card up to remove it from the guide glass (if any), and lay on a flat surface next to the door.
The main point: Clicking clips requires patience. If you feel strong resistance, stop and check for hidden screws to avoid breaking the plastic.
Disabling wiring and mechanisms
Now that the card is removed from the mounts, it is necessary to disconnect all electrical connectors. On the back of the panel. Skoda Tour You will see wires going to the speaker, backlight and window control buttons. Press the locker of the connector and pull it on yourself, without pulling the wires themselves.
Pay special attention to the speaker connector. Often it has a specific shape and can be fixed with an additional stopper. If you are planning to install new equipment, check the contact match. In older cars, the wires can be oxidized, so clean them carefully before reconnecting.
If you remove the card to access the lock mechanism, you also need to disconnect the lock drive cable. It is attached to a plastic pen inside the card. Press the rope locker and carefully remove it from the grooves. Be very careful as the plastic clamp is very fragile.
| Component | Mounting type | Features of dismantling |
|---|---|---|
| Speaker | Locker connector | Push the tongue and pull |
| Lock cable | Plastic clamp | Carefully remove from the groove, do not break |
| Power window buttons | Transverse plume | Click the locks carefully. |
| Backlight | The plug-in | Press the latch of the connector |
โ ๏ธ Attention: When disconnecting the lock cable, do not use a screwdriver to smear the lock. This can cause it to break down and the mechanism will stop opening from the inside. Use only your fingers.
After turning off all connectors, carefully examine the inside of the card. Make sure there are no sticky parts left on it, such as soundproofing film or parts of the insulation. If they are unstuck, do not throw them away โ they will need to be returned to the place when assembled.
If the speaker connector is tight, heat it with a hairdryer. The plastic will become softer, and the fixator will be easier to press, which will reduce the risk of breakage.
Design features of Skoda Tour doors
Model doors Skoda Tour They have their own design nuances that distinguish them from newer generations. The main feature is the method of fastening the sound insulation membrane. In most cases, it is glued to a metal door, and when you remove the card it can be damaged.
If you plan to install additional equipment, for example, noise insulation, then the old membrane is better to be carefully removed and replaced with a new material. However, if you are simply changing the speaker, try not to tear the factory film. The tearing of the vapor-insulating film will lead to moisture entering the door module, which can cause corrosion and malfunction of the electronics.
It is also worth noting the location of the wire harnesses. V Skoda Tour They often pass through rubber corrugated in the body rack. When assembly, make sure the tourniquet is not twisted or clamped, otherwise this can lead to oxidation of the contacts or to the breaking of the wires over time.
- ๐ก๏ธ Check the integrity of the vapor insulation film on the door
- ๐ก๏ธ Inspect the rubber corrugated at the connection with the body
- ๐ก๏ธ Make sure the wires are not pulled when closing the door.
The secret of membrane fastening
The factory membrane is often attached to butyl mastic. If it cracks, it is easy to restore it by heating it with a hair dryer and pressing it against the metal.
When working with the window lifter mechanism, remember that the guides can be plastic or metal. Depending on the year of issue Skoda TourThe material may be different. Plastic guides are more fragile and require careful handling when mounting the glasses back.
Main idea: Preserving the integrity of the vapor insulation is critical for the durability of the door structure and preventing corrosion of metal elements.
Correct assembly and performance testing
The door is assembled in reverse order. First, connect all the electrical connectors and fasten the lock cable. Make sure that the cable is pulled correctly and the lock mechanism works smoothly, without jamming. Test the opening and closing of the door from the inside and outside.
Before you snap the clips, make sure that the card is flat and does not sway. Put the card in the upper groove, then gently press it around the perimeter. You should hear clear snaps of fixation. If some area is not snapped, do not press with force - check whether the wire is clamped somewhere.
After installing all clips, twist the screws of the mounting. Do not over-tighten them as the plastic may crack. Put the decorative stubs in place. Then, put them in until they are full of water or a sleeve.
- โ Check the windows before installing the card
- โ Make sure the card fits tightly around the perimeter
- โ Check the operation of the central lock from the inside and outside
โ ๏ธ Attention: If after assembly you hear a knock or vibration, it means that one of the clips did not sit in the groove or there was an extra object inside. Take the door apart again and check the mounts.
At the end of the process, wipe the surface of the door and map from finger marks and dust. If you have used lubricant for mechanisms, make sure it does not fall on the plastic. Cleanliness and accuracy of the assembly is the guarantee that the door will not creak in the future.
Now yours Skoda Tour ready for operation again. Properly removed and installed door card will provide reliable protection of internal mechanisms and will preserve the aesthetic appearance of the car interior.
Frequently asked questions (FAQ)
How long does it take to remove the door card on the Skoda Tour?
The average process takes 15 to 30 minutes per door, depending on your experience and the tools you need. If youโre doing it for the first time, spend more time looking for hidden screws.
What to do if the plastic piston breaks during removal?
Don't panic. Broken piston can be replaced by a new one, buying a universal set of clips for cars. If the fixture on the card itself is broken, it can be carefully glued or a metal screw with a washer is used as a temporary solution.
Do I need to remove the glass before removing the card?
No, you don't have to take the glass off. The map is taken off over the glass, just make sure the glass is raised to the point upwards so that it does not interfere with the removal of the top of the skin.
Can I take a card without special shoulder blades?
Technically possible, using an old bank card or plastic line. However, the risk of damage to plastic or paint coatings increases significantly, so the use of special tools is highly recommended.
How to check if the speaker is turned off if the card is already removed?
Go to the door and press the opening button. If the speaker is off, there's no sound. You can also visually check the connector on the back of the card - it must be disconnected.