Removing the rear seat of a Škoda Superb: instructions with photos and tips

Removing the rear seat Škoda Superb may be required in a variety of situations: from banal interior cleaning to electronics repair, replacement of upholstery, or even installation of additional equipment (for example, a subwoofer or battery). However, many owners encounter difficulties - unobvious latches, hidden bolts or fear of damaging plastic elements. This article will help you understand all the nuances of the process, avoid mistakes and save time.

We will look at the features of removing the seat for different generations of the model (B6, B7/FL, 3V), we will indicate the necessary tools and warn against common mistakes. And if you plan to clean or repair after dismantling, at the end of the article you will find useful tips on caring for the seats and interior.

Preparing for dismantling: tools and safety precautions

Before you get started, make sure you have everything you need on hand. For basic seat removal (without dismantling the backrest) a minimal set is enough, but if you are planning a complete disassembly, prepare more thoroughly.

• 🔧 Tools: socket wrench 10 mm (or a socket with a ratchet), a flat-head screwdriver (for prying up plastic clips), pliers, a flashlight.
• 🧹 For cleaning: vacuum cleaner, wet wipes, fabric cleaner (if you wash the seat).
• 📦 Additionally: plastic film (so as not to stain the interior), marker (for marking fasteners), rubber gloves.

Important: if your Superb equipped heated seats or electric adjustment, before starting work disconnect the negative terminal of the battery. This will prevent a short circuit if the wiring is accidentally damaged. Also keep in mind that after disconnecting the battery, the settings of the radio and on-board computer may be reset - write down important data in advance.

⚠️ Attention: On models Superb 3V (2015–present) the system wiring harness runs under the rear seat START-STOP. Sudden movements can damage the connectors - proceed carefully!

Step-by-step instructions: how to remove the lower part of the seat

Let's start with the simplest thing - dismantling bottom seat cushion. This process is the same for all generations Superb, with the exception of minor nuances.

1. Lower the seat back. If your configuration has the function 60/40, lower both parts or the one you plan to remove.
2. Locate the fasteners at the front. Use a screwdriver to pry up the plastic trim at the base of the seat (from the side of the passengers' feet). There are two bolts hidden underneath 10 mm.
3. Unscrew the bolts. Use a socket wrench or socket. The bolts may be tight - do not use excessive force to avoid stripping the threads.
4. Move the seat forward. After unscrewing the bolts, the pillow should move easily along the guides. If this does not happen, check to see if any fastenings have gone unnoticed.
5. Disconnect the connectors (if any). On models with heating or occupancy sensors, there will be wires under the seat. Carefully separate them without pulling the wires.

On Superb B6 fastenings may differ - plastic latches are sometimes used instead of bolts. In this case, they need to be carefully snapped off with a screwdriver, starting from the corner of the seat. If the latch is broken, don’t worry, it’s easy to replace (original part number: 1U0 881 201).

Features of dismantling the seat back

Removal rear seat backs required less often, but may be needed to replace the trim, repair the folding mechanism, or access luggage compartment (for example, to install speakers). Here the algorithm of actions depends on the generation of the car.

Generation	Backrest mounting type	Tools	Nuances
Superb B6 (2001–2008)	4 bolts per 13 mm + plastic clips	Head 13, screwdriver	The bolts are hidden under decorative plugs in the trunk
Superb B7/FL (2008–2015)	2 bolts per 10 mm + latches	10mm socket wrench, pliers	The latches are fragile - pry them off carefully
Superb 3V (2015–present)	Clips + 1 bolt per T25 (in the center)	Torx T25, plastic puller	The backrest is attached to the body through rubber bushings

On Superb 3V the backrest is additionally fixed folding mechanism cable. To disconnect it you will need:

1. Remove the plastic trim in the trunk (pry it off with a screwdriver).
2. Find the metal hook of the cable and carefully move it to the side, freeing the backrest.
3. When reassembling, make sure that the cable is not twisted - otherwise the folding mechanism will not work correctly.

⚠️ Attention: On models with climate control panel for rear passengers (optional Rear Air Conditioning) air ducts pass under the backrest. Do not press on them - the plastic may crack!

What to do if the seat cannot be removed: typical problems

Even if you follow the instructions exactly, sometimes difficulties arise. Let's look at the most common situations and ways to solve them.

• 🔩 The bolts do not come off. Possible causes: corrosion, stripped threads, or excessive force during previous assembly. Solution: Treat the bolts with a penetrating lubricant (e.g. WD-40) and wait 10–15 minutes. If it doesn't help, use it extractor for broken bolts.
• 🔌 The connectors are not disconnected. On heated models, the connectors may “stick”. Do not pull the wires - gently rock the connector from side to side while pressing the latch.
• 🔧 The seat is stuck in the guides. Often found on Superb B6 due to deformation of metal runners. Solution: Lubricate the guides with silicone grease and try to move the seat by rocking it left and right.

If you encounter broken plastic clips, do not try to assemble the seat without them - it will dangle and rattle. Replace the clips with new ones (they cost pennies, and original part numbers can be found in the catalog ETKA). For a temporary solution, clips from VW Passat B6 - they are identical in size.

How to remove a broken bolt from a guide?

If a bolt breaks off while unscrewing, don't panic. Take a drill with a diameter 1-2 mm smaller than the diameter of the bolt and carefully drill a hole in the center. Then use an extractor (or even a reverse thread screw) to remove the remaining bits. After this, cut the new thread with a tap of the appropriate size.

Cleaning and maintaining seats after dismantling

Once the seat is removed, you have a great opportunity to tidy it up. This is especially true for cars with high mileage, where dust, sand and even small debris accumulate under the cushion.

• 🧽 Dry cleaning. Use a vacuum cleaner with a narrow attachment to remove sand and crumbs from under the seat. Please note guides - Dirt often accumulates there.
• 💦 Wet cleaning. For fabric upholstery, a foam cleaner (for example, Autoglym Interior Shampoo). Apply the foam, let it soak in for 5-10 minutes, then remove with a damp microfiber. For leather seats, use special conditioners.
• 🔍 Checking mechanisms. Inspect the springs and foam for wear. If the springs are rusty or the foam is crumbling, this is a sign that the seat will soon require repair.

For disinfection In the cabin, you can use an ozonizer or a steam generator. This is especially true if there were pets in the car or it sat in a damp garage for a long time. After cleaning, allow the seat to dry completely before installing it - moisture under the upholstery can cause mold.

Reinstalling the seat: nuances and verification

Assembly is no less important stage than dismantling. It is important here not only to secure everything in place, but also to make sure that the seat functions correctly. Let's start with sequences of actions:

1. Check the guides. Make sure there is no debris or sand in them. If necessary, lubricate them with silicone grease.
2. Connect the connectors. If you disconnected the wiring, return the connectors to their place until the seat is secured. On Superb 3V pay attention to START-STOP system harness - it should not be tense.
3. Install the seat cushion. Start with the rear mounts, then slide the front onto the rails and secure with bolts. Tighten them crosswise to avoid distortion.
4. Check the backrest. If you removed it, make sure that the folding mechanism cable is not twisted and that the backrest is locked in both positions.

After installation it is necessary test the seat:

• 🔄 Check the backrest folding mechanism (if equipped).
• 🔥 Turn on the heat (if equipped) and make sure both sides are heating.
• 🚗 Drive on uneven roads - the seat should not squeak or wobble.

⚠️ Attention: If the light comes on after installation Airbag (on models with rear side airbags), you have damaged the connector or wiring. Immediately disconnect the battery and check the circuit!

Modifications and tuning: what can be done after removing the seat

Removing the rear seat opens up possibilities for tuning and modernization salon Here are some popular options:

• 🎵 Installing a subwoofer or amplifier. In a niche under the seat you can place a compact subwoofer (for example, JBL BassPro SL), without sacrificing useful trunk space.
• 🔋 Additional battery. For cars with powerful acoustics or off-road modifications, install a second battery (for example, Optima YellowTop). Important: use denouement of the massesto avoid conflicts with the main battery.
• 💺 Replacing the casing. Worn fabric or leather can be replaced with a new one, choosing the material to match the interior tone or, on the contrary, making an accent (for example, upholstery Alcantara with red lines).
• 🔌 Additional sockets/USB. You can install a socket in the cup holders or a niche under the seat. 12V or USB hub for rear passengers.

If you plan to install electrical equipment, consider the load on the on-board network. For example, a powerful subwoofer (500W+) will require a separate power cable from the battery with a fuse. To do this, you will have to remove the trunk trim - we will talk about this in a separate article.

FAQ: Frequently asked questions about removing the rear seat of a Škoda Superb

Can the seat be removed without tools?

Theoretically - yes, if you have Superb B7/FL or 3V with plastic latches. But in practice, without a screwdriver or wrench, you risk breaking the clips or scratching the plastic. For bolts, a tool is required.

How long does dismantling take?

For an experienced master - 15–20 minutes. If this is your first time doing this, please 40–60 minutes (including cleaning and reassembly). On Superb B6 the process may take longer due to rusty bolts.

What happens if you do not disconnect the battery before work?

If the seat has electronics (heating, sensors), you risk shorting wires or blowing a fuse. On Superb 3V this may lead to an error in the control unit BCM, which can only be reset using a diagnostic scanner.

Can the seat be washed with a hose?

Absolutely not! The foam padding will absorb moisture, and the seat will dry for weeks, and the inside will begin to mold. Use only a damp sponge or steam generator followed by drying.

Where can I buy spare parts for seat mounts?

Original parts (bolts, clips, guides) can be ordered by VIN code from an authorized dealer Škoda or in online stores (for example, Exist.ru, Emex.ru). Look for analogues by article numbers in the catalog ETKA.